Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019701 NAVIGATION / MULTI INFO DISPLAY _0101135 NAVIGATION SYSTEM(for Radio and Display Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  B1324  Lost Communication with Meter  


DESCRIPTION

This DTC is stored when a communication error occurs between the radio and display receiver assembly and combination meter assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1324 Lost Communication with Meter After the radio and display receiver assembly receives a registration information signal, which is sent by the combination meter assembly when the engine switch is on (ACC), 1 or more times, the radio and display receiver assembly cannot receive the signal for 30 seconds or more.
·

Combination meter assembly

·

Radio and display receiver assembly

·

Harness or connector



WIRING DIAGRAM

E268494E98
1.656,0.438 2.271,0.635 0.615,0.198 10 false MSCH 1.667,1.083 2.281,1.281 0.615,0.198 10 false MSCL 5.083,0.427 5.698,0.625 0.615,0.198 10 false CNH1 5.094,1.083 5.708,1.281 0.615,0.198 10 false CNL1 2.146,0.292 2.76,0.49 0.615,0.198 10 false 29 2.135,0.938 2.75,1.135 0.615,0.198 10 false 30 4.906,0.292 5.521,0.49 0.615,0.198 10 false 3 4.906,0.927 5.521,1.125 0.615,0.198 10 false 4 0.781,1.594 1.396,1.792 0.615,0.198 10 false F126 0.781,1.75 2.75,1.979 1.969,0.229 10 false Combination Meter Assembly 4.781,1.583 5.396,1.781 0.615,0.198 10 false F72 4.781,1.74 6.469,2.104 1.688,0.365 10 false Radio and Display Receiver Assembly 0.906,2.24 3.271,2.469 2.365,0.229 10 false : Local Bus Communication Line

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F72 radio and display receiver assembly connector.


b.

Disconnect the F126 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F72-3 (CNH1) - F126-29 (MSCH) Always Below 1 Ω
F72-4 (CNL1) - F126-30 (MSCL) Always Below 1 Ω
F72-3 (CNH1) - Body ground Always 10 kΩ or higher
F72-4 (CNL1) - Body ground Always 10 kΩ or higher
F72-3 (CNH1) - F72-4 (CNL1) Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F72-3 (CNH1) - Body ground Always Below 1 V
F72-4 (CNL1) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT COMBINATION METER ASSEMBLY
a.

Remove the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.
E305050C02
1.896,1.927 2.344,2.521 false 1.729,1.948 1.281,2.51 false 2.344,2.542 2.833,2.865 0.49,0.323 10 false MSCH 1.094,2.542 1.563,2.885 0.469,0.344 10 false MSCL 0.146,0.5 0.615,0.844 0.469,0.344 10 false *a
*a Component without harness connected
(Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
29 (MSCH) - 30 (MSCL) Always 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Remove the radio and display receiver assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.
E286972C02
2.094,1.729 2.333,1.167 false 1.99,1.729 1.781,1.167 false 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 2.292,0.99 2.906,1.188 0.615,0.198 10 false CNH1 1.5,0.99 2.115,1.188 0.615,0.198 10 false CNL1
*a Component without harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (CNH1) - 4 (CNL1) Always 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

4.REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new or known good one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

5.CHECK METER / GAUGE SYSTEM

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

5.CHECK METER / GAUGE SYSTEM
a.

Turn the engine switch on (IG) and wait 30 seconds.


b.

Operate the steering pad switch assembly and check that the audio tab is displayed on the multi-information display in the combination meter assembly and the audio system can be operated normally.

OK:

Audio system returns to normal.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY