When an open or short circuit is detected in the transponder key amplifier coil built into the engine switch, the certification ECU (smart key ECU assembly) stores this DTC. This DTC is also stored as a past DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B2784 | Antenna Coil Open / Short | The transponder key amplifier coil built into the engine switch is open (see below) or shorted (determined by communication with certification ECU (smart key ECU assembly)). (1 trip detection logic*)
·
Terminal AGND, VC5, TXCT or CODE circuit is open (includes disconnection of the engine switch). ·
The transponder key amplifier coil built into the engine switch is open. |
·
Engine switch ·
Certification ECU (smart key ECU assembly) ·
Wire harness or connector |
DTC output confirmation operation:
With the shift lever in P and the key held near the engine switch, an engine start operation is performed by pressing and holding the engine switch when the transmitter battery is depleted. |
*: Only output while a malfunction is present.
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
| Engine cannot be started when transmitter battery is depleted by holding transmitter near engine switch and pressing and holding engine switch with shift lever in P | - |
| DTC No. | Data List and Active Test |
|---|---|
| B2784 | - |
When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
Disconnect the F13 certification ECU (smart key ECU assembly) connector.
Disconnect the F49 engine switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F13-13 (CODE) - F49-8 (CODE) | Always | Below 1 Ω |
| F13-14 (TXCT) - F49-7 (TXCT) | Always | Below 1 Ω |
| F13-15 (VC5) - F49-10 (VC5) | Always | Below 1 Ω |
| F13-12 (AGND) - F49-6 (AGND) | Always | Below 1 Ω |
| F13-13 (CODE) or F49-8 (CODE) - Body ground | Always | 10 kΩ or higher |
| F13-14 (TXCT) or F49-7 (TXCT) - Body ground | Always | 10 kΩ or higher |
| F13-15 (VC5) or F49-10 (VC5) - Body ground | Always | 10 kΩ or higher |
| F13-12 (AGND) or F49-6 (AGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the engine switch with a new or known good one.
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS STARTING>ENGINE SWITCH>REMOVAL
for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE STARTING>ENGINE SWITCH>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Perform "DTC Output Confirmation Operation" procedure.
Check for DTCs.
DTC B2784 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG