Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Smart Entry and Start System) › from 2016.11
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0095462 IMMOBILISER SYSTEM(w/ Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Smart Entry and Start System)  B278A  Short to GND in Immobiliser System Power Source Circuit  


DESCRIPTION

When there is a short to GND in the power supply for the transponder key amplifier of the engine switch, the certification ECU (smart key ECU assembly) stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B278A Short to GND in Immobiliser System Power Source Circuit A short to GND in the power supply of the transponder key amplifier of the engine switch (VC5 - VC5) detected. (1 trip detection logic*)
·

Engine switch

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


DTC output confirmation operation:

With the shift lever in P and the key held near the engine switch, an engine start operation is performed by pressing and holding the engine switch when the transmitter battery is depleted.



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started when transmitter battery is depleted by holding transmitter near engine switch and pressing and holding engine switch with shift lever in P -

Related Data List and Active Test
DTC No. Data List and Active Test
B278A -

WIRING DIAGRAM

B308510E18
5.094,2.854 5.458,3.052 0.365,0.198 10 false F13 5.094,3.01 6.729,3.427 1.635,0.417 10 false Certification ECU (Smart Key ECU Assembly) 0.896,2.865 1.25,3.031 0.354,0.167 10 false F49 0.885,3.01 2.865,3.219 1.979,0.208 10 false Engine Switch 1.917,2.25 2.094,2.438 0.177,0.188 10 false 6 5.01,1.698 5.188,1.885 0.177,0.188 10 false 13 1.917,1.198 2.094,1.385 0.177,0.188 10 false 7 1.896,0.688 2.073,0.875 0.177,0.188 10 false 10 5,2.219 5.177,2.406 0.177,0.188 10 false 12 5.26,2.333 5.74,2.531 0.479,0.198 10 false AGND 5.25,1.823 5.74,2.031 0.49,0.208 10 false CODE 5.25,1.313 5.74,1.552 0.49,0.24 10 false TXCT 5.25,0.792 5.698,1.052 0.448,0.26 10 false VC5 1.427,2.333 1.948,2.583 0.521,0.25 10 false AGND 1.917,1.719 2.094,1.906 0.177,0.188 10 false 8 1.417,1.823 1.938,2.104 0.521,0.281 10 false CODE 5.021,1.208 5.198,1.396 0.177,0.188 10 false 14 1.469,1.313 1.958,1.521 0.49,0.208 10 false TXCT 5.01,0.677 5.188,0.865 0.177,0.188 10 false 15 1.542,0.792 1.99,0.979 0.448,0.188 10 false VC5

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Using an oscilloscope, check the waveform.

B345599C15
1.927,0.375 2.271,0.594 0.344,0.219 1.354,2.302 1.865,1.625 false 2.771,2.313 2.354,1.625 false 1.49,0.375 1.802,0.573 0.313,0.198 10 false *a 1.99,0.396 2.302,0.594 0.313,0.198 10 false F49 6.51,1.375 6.823,1.573 0.313,0.198 10 false GND 1.219,2.333 1.531,2.531 0.313,0.198 10 false VC5 2.625,2.333 3.052,2.531 0.427,0.198 10 false AGND
*a Component with harness connected
(Engine Switch)
- -


HINT:

Perform this inspection on the engine switch side.


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
F49-10 (VC5) - F49-6 (AGND) Engine switch off, key not in cabin, within 30 seconds after engine switch pressed 2 V/DIV., 200 ms./DIV. Pulse generation


OK:

The waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)
2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)
a.

Disconnect the F13 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F49 engine switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F13-15 (VC5) - F49-10 (VC5) Always Below 1 Ω
F13-12 (AGND) - F49-6 (AGND) Always Below 1 Ω
F13-15 (VC5) or F49-10 (VC5) - Body ground Always 10 kΩ or higher
F13-12 (AGND) or F49-6 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the F13 certification ECU (smart key ECU assembly) connector.


b.

Reconnect the F49 engine switch connector.


c.

Measure the voltage according to the value(s) in the table below.

B343119C15
3.292,0.281 3.698,0.51 0.406,0.229 5.083,0.292 5.49,0.521 0.406,0.229 1.615,0.281 2.021,0.51 0.406,0.229 5.313,2.156 5.51,2.156 5.51,2.156 5.542,1.104 false 6.354,2.167 6.208,2.167 6.208,2.167 5.938,1.094 false 6.427,2.115 6.885,2.313 0.458,0.198 10 false AGND 5.188,0.313 5.646,0.51 0.458,0.198 10 false F13 5.01,2.104 5.469,2.302 0.458,0.198 10 false VC5 0.302,0.146 0.76,0.344 0.458,0.198 10 false *a 3.385,0.302 3.844,0.5 0.458,0.198 10 false F12 1.708,0.302 2.167,0.5 0.458,0.198 10 false F10
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Standard Voltage:
Tester Connection Condition Specified Condition
F13-15 (VC5) - F13-12 (AGND) Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)