Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Smart Entry and Start System) › from 2016.11
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0095462 IMMOBILISER SYSTEM(w/ Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Smart Entry and Start System)  B279A  Theft Deterrent System Communication Line High Fixation  B279A12  Engine Immobiliser System Circuit Short to Battery  


DESCRIPTION

When the communication line (IMI - EFIO) between the ECM and ID code box (immobiliser code ECU)*2 or certification ECU (smart key ECU assembly)*3 is stuck high, the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279A Theft Deterrent System Communication Line High Fixation The communication line (IMI - EFIO) between the ECM and ID code box (immobiliser code ECU)*2 or certification ECU (smart key ECU assembly)*3 is stuck high. (1 trip detection logic*1)
·

ID code box (immobiliser code ECU)*2

·

Certification ECU (smart key ECU assembly)*3

·

ECM

·

Wire harness or connector


DTC output confirmation operation:

Turn the engine switch on (IG) and wait 6 seconds.


B279A12 Engine Immobiliser System Circuit Short to Battery The communication line (IMI - EFIO) between the ECM and ID code box (immobiliser code ECU)*2 or certification ECU (smart key ECU assembly)*3 is stuck high. (1 trip detection logic*1)
·

ID code box (immobiliser code ECU)*2

·

Certification ECU (smart key ECU assembly)*3

·

ECM

·

Wire harness or connector


DTC output confirmation operation:

Turn the engine switch on (IG) and wait 6 seconds.



*1: Only output while a malfunction is present.

*2: w/ Rear Seat Heater

*3: w/o Rear Seat Heater


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started Engine cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
·

B279A*1

·

B279A12*2


-

*1: for 1AR-FE

*2: for 2GR-FKS


WIRING DIAGRAM

w/ Rear Seat Heater


B366893E30
1.802,0.885 2.573,1.073 0.771,0.188 10 false 28*1, 59*2 5.271,0.896 5.49,1.073 0.219,0.177 10 false 4 1.469,1.01 1.875,1.24 0.406,0.229 10 false IMI 5.479,1 5.885,1.229 0.406,0.229 10 false EFIO 1.083,1.823 1.49,2.052 0.406,0.229 10 false A43 1.073,1.979 1.479,2.208 0.406,0.229 10 false ECM 5.115,1.802 5.521,2.031 0.406,0.229 10 false F67 5.115,1.958 6.708,2.406 1.594,0.448 10 false ID Code Box (Immobiliser Code ECU) 2.583,1.979 3.656,2.229 1.073,0.25 10 false *1: for 1AR-FE 2.583,2.292 3.656,2.542 1.073,0.25 10 false *2: for 2GR-FKS


w/o Rear Seat Heater


B366893E31
1.802,0.885 2.573,1.073 0.771,0.188 10 false 59 5.271,0.896 5.49,1.073 0.219,0.177 10 false 6 1.469,1.01 1.875,1.24 0.406,0.229 10 false IMI 5.479,1 5.885,1.229 0.406,0.229 10 false EFIO 1.083,1.823 1.49,2.052 0.406,0.229 10 false A43 1.073,1.979 1.479,2.208 0.406,0.229 10 false ECM 5.146,1.802 5.552,2.031 0.406,0.229 10 false F10 5.146,1.958 6.688,2.396 1.542,0.438 10 false Certification ECU (Smart Key ECU Assembly)


CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the ECM, ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2, refer to Service Bulletin.

*1: w/ Rear Seat Heater

*2: w/o Rear Seat Heater


·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When DTC B279A*1 or B279A12*2 and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


*1: for 1AR-FE

*2: for 2GR-FKS


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234
Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Turn the engine switch on (IG) and wait 10 seconds.


b.

Check for DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Powertrain > Engine > Trouble Codes
50001 372
HINT:

If DTCs other than DTC B279A*1 or B279A12*2 are output, troubleshoot those DTCs first.



Result:
Result Proceed to
DTC B279A*1 or B279A12*2 is output A
DTC B279A*1 or B279A12*2 and other DTCs are output B


*1: for 1AR-FE

*2: for 2GR-FKS



A

3.CHECK CONNECTION OF CONNECTOR

B

3.CHECK CONNECTION OF CONNECTOR
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the ECM and ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2.

*1: w/ Rear Seat Heater

*2: w/o Rear Seat Heater


OK:

Connectors are properly connected.



Result:
Result Proceed to
OK (w/ Rear Seat Heater) A
OK (w/o Rear Seat Heater) B
NG C



A

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

B

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

C

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
a.

Disconnect the F67 ID code box (immobiliser code ECU) connector.


b.

Disconnect the A43 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F67-4 (EFIO) - A43-59 (IMI)*2 Always Below 1 Ω
F67-4 (EFIO) - A43-28 (IMI)*1 Always Below 1 Ω
F67-4 (EFIO) or A43-59 (IMI) - Body ground*2 Always 10 kΩ or higher
F67-4 (EFIO) or A43-28 (IMI) - Body ground*1 Always 10 kΩ or higher


*1: for 1AR-FE

*2: for 2GR-FKS



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A43-59 (IMI) - Body ground*2 Always 11 to 14 V
A43-28 (IMI) - Body ground*1 Always 11 to 14 V


*1: for 1AR-FE

*2: for 2GR-FKS



Result:
Proceed to
OK
NG



OK

5.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

8.REGISTER RECOGNITION CODE
6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

Disconnect the F10 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A43 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F10-6 (EFIO) - A43-59 (IMI) Always Below 1 Ω
F10-6 (EFIO) or A43-59 (IMI) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A43-59 (IMI) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

8.REGISTER RECOGNITION CODE
8.REGISTER RECOGNITION CODE
a.

Register the recognition codes in the ECUs.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.REGISTER ECU COMMUNICATION ID
9.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
10.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT



NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.


b.

Check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372
OK:

B279A12 is not output.



Result:
Proceed to
OK
NG



OK

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

NG