Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Smart Entry and Start System) › from 2016.11
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0095462 IMMOBILISER SYSTEM(w/ Smart Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Smart Entry and Start System)  Security Indicator Light Does not Blink  


DESCRIPTION

·

The certification ECU (smart key ECU assembly) blinks the security indicator light (clock assembly) when the immobiliser is set (engine switch off, or driver door opened and closed with engine switch on (IG)).

·

The certification ECU (smart key ECU assembly) receives the security indicator light signal from the main body ECU (multiplex network body ECU) via CAN communication when the theft deterrent system is in the arming preparation state or alarm sounding state. Then, the certification ECU (smart key ECU assembly) blinks the security indicator light (clock assembly).


WIRING DIAGRAM

B352108E05
0.813,3.427 2.74,3.625 1.927,0.198 10 false : CAN Communication Line 0.948,1.094 1.104,1.292 0.156,0.198 10 false E 1.906,0.99 2.063,1.188 0.156,0.198 10 false 9 0.771,0.99 0.927,1.188 0.156,0.198 10 false 8 1.646,1.094 1.875,1.302 0.229,0.208 10 false LP 2.948,0.969 3.156,1.146 0.208,0.177 10 false 19 3.167,1.083 3.469,1.281 0.302,0.198 10 false IND 2.833,1.792 3.156,2 0.323,0.208 10 false F13 5.198,1.906 6.813,2.281 1.615,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 2.823,1.948 4.646,2.344 1.823,0.396 10 false Certification ECU (Smart Key ECU Assembly) 0.75,1.458 1.031,1.656 0.281,0.198 10 false G7 0.75,1.615 2.219,1.979 1.469,0.365 10 false Security Indicator Light (Clock Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

The immobiliser system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the immobiliser system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
Powertrain > Engine and ECT > Trouble Codes
50001 234
Powertrain > Engine > Trouble Codes
50001 372
OK:

DTCs are not output.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS (IMMOBILISER INDICATOR)

NG

2.PERFORM ACTIVE TEST USING GTS (IMMOBILISER INDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Entry&Start > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Immobiliser Indicator Security indicator light OFF/ON -
Body Electrical > Entry&Start > Active Test
Tester Display
Immobiliser Indicator
50004 125 28
OK:

The security indicator light (clock assembly) operates normally.



Result:
Result Proceed to
OK (w/ Theft Deterrent System) A
OK (w/o Theft Deterrent System) B
NG C



A

3.CHECK SECURITY INDICATOR LIGHT (CLOCK ASSEMBLY) OPERATION

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

C

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SECURITY INDICATOR LIGHT (CLOCK ASSEMBLY) - BODY GROUND)
3.CHECK SECURITY INDICATOR LIGHT (CLOCK ASSEMBLY) OPERATION
a.

When the immobiliser is set, check that the security indicator light (clock assembly) blinks.*1

OK:

The security indicator light (clock assembly) blinks normally.



b.

When the theft deterrent system is in the arming preparation state, check that the security indicator light (clock assembly) illuminates.*2

OK:

The security indicator light (clock assembly) illuminates normally.



Result:
Result Proceed to
*1 is NG (*2 is OK) A
*2 is NG (*1 is OK) B



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SECURITY INDICATOR LIGHT (CLOCK ASSEMBLY) - BODY GROUND)
a.

Disconnect the F13 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G7 security indicator light (clock assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F13-19 (IND) - G7-9 (LP) Always Below 1 Ω
F13-19 (IND) or G7-9 (LP) - Body ground Always 10 kΩ or higher
G7-8 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the F13 certification ECU (smart key ECU assembly) connector.


b.

Reconnect the G7 security indicator light (clock assembly) connector.


c.

Using an oscilloscope, check the waveform.

B343119C16
5.073,0.229 5.5,0.458 0.427,0.229 1.708,0.229 2.115,0.479 0.406,0.25 3.323,0.219 3.729,0.458 0.406,0.24 4.792,2.198 5.177,1.104 false 5.177,0.26 5.625,0.438 0.448,0.177 9 false F13 4.698,2.219 5.156,2.417 0.458,0.198 10 false IND 0.302,0.146 0.76,0.344 0.458,0.198 10 false *a 3.406,0.25 3.719,0.448 0.313,0.198 10 false F12 1.792,0.25 2.25,0.448 0.458,0.198 10 false F10
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Measurement Condition:
Tester Connection Condition Specified Condition
F13-19 (IND) - Body ground Engine switch off → on (IG) Pulse generation → Below 2 V



Result:
Proceed to
OK
NG



OK

REPLACE SECURITY INDICATOR LIGHT (CLOCK ASSEMBLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)