Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › from 2016.11
RM3160E _58 Vehicle Interior _019707 LIGHTING (INT) _0103507 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  IG Signal Circuit  


DESCRIPTION

This circuit detects the ignition switch ON or off condition, and sends it to the main body ECU (multiplex network body ECU).

WIRING DIAGRAM

E361741E01
0.438,0.698 1.417,0.927 0.979,0.229 10 false from Battery 0.333,1.094 1.313,1.323 0.979,0.229 10 false from ALT Fuse 1.771,0.833 2.198,1.063 0.427,0.229 10 false ALT 1.635,1.24 2.49,1.448 0.854,0.208 10 false J/B-ALT 2.625,0.719 3,0.917 0.375,0.198 10 false 4K 2.615,1.49 2.99,1.688 0.375,0.198 10 false 4A 2.625,2.094 3,2.292 0.375,0.198 10 false 4F 2.625,2.625 3,2.823 0.375,0.198 10 false 4F 2.635,3.083 3.01,3.281 0.375,0.198 10 false 4A 3.781,1.771 4.563,2.01 0.781,0.24 10 false IG1 NO. 3 4.823,0.854 5.604,1.094 0.781,0.24 10 false IG1 NO. 3 2.948,3.667 5.865,3.896 2.917,0.229 10 false Instrument Panel Junction Block Assembly 5.375,4.115 7.01,4.5 1.635,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 5.365,3.969 5.719,4.188 0.354,0.219 10 false MB 0.115,1.51 1.24,2.365 1.125,0.854 10 false from Certification ECU (Smart Key ECU Assembly)*1 or Ignition Switch Assembly*2 0.135,4.104 2.469,4.333 2.333,0.229 10 false *1: w/ Smart Entry and Start System 0.135,4.396 2.563,4.656 2.427,0.26 10 false *2: w/o Smart Entry and Start System 2.698,4.083 4.323,4.26 1.625,0.177 10 false *3: for 1AR-FE 2.708,4.396 4.333,4.573 1.625,0.177 10 false *4: for 2GR-FKS 2.667,0.51 2.823,0.708 0.156,0.198 10 false 1 2.646,1.302 2.885,1.531 0.24,0.229 10 false 16 2.625,1.896 2.865,2.125 0.24,0.229 10 false 19 2.635,2.427 2.875,2.656 0.24,0.229 10 false 24 2.635,2.885 2.875,3.115 0.24,0.229 10 false 27 5.875,2.531 6.115,2.76 0.24,0.229 10 false 32 6.156,2.625 6.396,2.854 0.24,0.229 10 false IG 2.125,0.625 2.438,0.823 0.313,0.198 10 false *3 2.125,1.01 2.438,1.208 0.313,0.198 10 false *4


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*1

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*2

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION


*1: w/ Smart Entry and Start System

*2: for LHD



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Smart Entry and Start System A
w/o Smart Entry and Start System B



A

2.CHECK FOR DTC (SMART ENTRY AND START SYSTEM (for Start Function))

B

7.READ VALUE USING GTS
2.CHECK FOR DTC (SMART ENTRY AND START SYSTEM (for Start Function))
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>DTC CHECK / CLEAR

Body Electrical > Power Source Control > Clear DTCs
50002 223

b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>DTC CHECK / CLEAR

Body Electrical > Power Source Control > Trouble Codes
50001 223

Result:
Result Proceed to
Smart Entry and Start System (for Start Function) DTCs are not output A
Smart Entry and Start System (for Start Function) DTCs are output B



A

3.READ VALUE USING GTS

B

3.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IG SW Ignition switch ON signal ON or OFF ON: Ignition switch ON
OFF: Ignition switch off
"OFF" is also displayed for this item when the ignition switch is ACC.
Body Electrical > Main Body > Data List
Tester Display
IG SW
50003 123 30
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

4.CHECK HARNESS AND CONNECTOR (BATTERY POWER SOURCE)
4.CHECK HARNESS AND CONNECTOR (BATTERY POWER SOURCE)
a.

Disconnect the 4K instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4K-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4F instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4F-19 - 4F-24 Always Below 1 Ω
4F-19 or 4F-24 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E288978C01
1.708,0.302 2.031,0.552 0.323,0.25 5.229,0.313 5.552,0.563 0.323,0.25 4.313,2.229 4.635,2.479 0.323,0.25 0.792,2.115 1.115,2.365 0.323,0.25 5.917,3.5 6.167,3.5 6.167,3.5 6.354,3.021 false 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 1.781,0.344 2.094,0.542 0.313,0.198 10 false 4A 5.333,0.365 5.646,0.563 0.313,0.198 10 false 4F 4.375,2.281 4.688,2.479 0.313,0.198 10 false MB 0.875,2.156 1.188,2.354 0.313,0.198 10 false 4K 5.688,3.417 6,3.615 0.313,0.198 10 false IG
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4K-1 - 4F-19 Battery not connected to 4A-16 and 4A-27 10 kΩ or higher
4K-1 - 4F-19 Battery positive (+) → 4A-16
Battery negative (-) → 4A-27
Below 1 Ω
4F-24 - MB-32 (IG) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

7.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IG SW Ignition switch ON signal ON or OFF ON: Ignition switch ON
OFF: Ignition switch off
"OFF" is also displayed for this item when the ignition switch is ACC.
Body Electrical > Main Body > Data List
Tester Display
IG SW
50003 123 30
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

8.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - IG1 NO. 3 RELAY POWER SOURCE AND BODY GROUND)
8.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - IG1 NO. 3 RELAY POWER SOURCE AND BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4A-16 - Body ground Ignition switch ON 11 to 14 V



b.

Disconnect the 4A instrument panel junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-27 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (BATTERY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (BATTERY POWER SOURCE)
a.

Disconnect the 4K instrument panel junction block assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4K-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4F instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4F-19 - 4F-24 Always Below 1 Ω
4F-19 or 4F-24 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E288978C01
1.708,0.302 2.031,0.552 0.323,0.25 5.229,0.313 5.552,0.563 0.323,0.25 4.313,2.229 4.635,2.479 0.323,0.25 0.792,2.115 1.115,2.365 0.323,0.25 5.917,3.5 6.167,3.5 6.167,3.5 6.354,3.021 false 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 1.781,0.344 2.094,0.542 0.313,0.198 10 false 4A 5.333,0.365 5.646,0.563 0.313,0.198 10 false 4F 4.375,2.281 4.688,2.479 0.313,0.198 10 false MB 0.875,2.156 1.188,2.354 0.313,0.198 10 false 4K 5.688,3.417 6,3.615 0.313,0.198 10 false IG
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4K-1 - 4F-19 Battery not connected to 4A-16 and 4A-27 10 kΩ or higher
4K-1 - 4F-19 Battery positive (+) → 4A-16
Battery negative (-) → 4A-27
Below 1 Ω
4F-24 - MB-32 (IG) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY