Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) › from 2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0296066 LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) C

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)  C1A71  Power Steering Control Torque  


DESCRIPTION

If the power steering ECU assembly detects an abnormality in the steering torque requested by the forward recognition camera, the power steering ECU assembly sends a malfunction signal to the forward recognition camera, and DTC C1A71 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A71 Power Steering Control Torque 2 seconds after the engine switch is turned on (IG), a malfunction signal from the power steering ECU assembly is detected by the forward recognition camera for 5 seconds or more.
·

Power steering system

·

Forward recognition camera

·

Power steering ECU assembly



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)

·

The lane departure alert system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTCs (POWER STEERING SYSTEM)
HINT:

Lane departure alert system DTC C1A71 may be stored due to a malfunction in the power steering system. Therefore it is necessary to check for and troubleshoot power steering system DTCs first.


a.

Check for DTCs are output.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DTC CHECK / CLEAR

Chassis > EMPS > Trouble Codes
50001 142

Result:
Result Proceed to
Power steering system DTCs are not output A
Power steering system DTCs are output B



A

2.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)

B

2.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
a.

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 7 seconds or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)>DTC CHECK / CLEAR

Chassis > LKA/LDA > Trouble Codes
50001 355

Result:
Result Proceed to
DTC C1A71 is not output A
DTC C1A71 is output B



A

B

3.REPLACE FORWARD RECOGNITION CAMERA
3.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL


b.

Perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
4.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
a.

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 7 seconds or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)>DTC CHECK / CLEAR

Chassis > LKA/LDA > Trouble Codes
50001 355

Result:
Result Proceed to
DTC C1A71 is not output A
DTC C1A71 is output B



A

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

B

REPLACE POWER STEERING ECU ASSEMBLY