The forward recognition camera receives vehicle stability signals from the yaw rate sensor (airbag sensor assembly). If the yaw rate sensor (airbag sensor assembly) detects an abnormal yaw rate sensor signal or yaw rate sensor power supply voltage, it informs the forward recognition camera via CAN communication, and DTC C1AA4 or C1AA5 is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1AA4 | Yaw Rate Sensor Circuit | When all of the following conditions are met:
·
2 seconds after the engine switch is turned on (IG) ·
The vehicle speed is 1 km/h or 1 mph or more. ·
A signal from the yaw rate sensor indicating a malfunction in the yaw rate sensor is detected by the forward recognition camera for 5 seconds or more. |
·
Vehicle stability control system ·
Yaw rate sensor (Airbag sensor assembly) ·
Forward recognition camera |
| C1AA5 | Yaw Rate Sensor Power Supply Voltage Circuit | When all of the following conditions are met:
·
2 seconds after the engine switch is turned on (IG) ·
The vehicle speed is 1 km/h or 1 mph or more. ·
A signal from the yaw rate sensor indicating an abnormal yaw rate sensor power supply voltage signal is detected by the forward recognition camera for 5 seconds or more. |
·
Vehicle stability control system ·
Yaw rate sensor (Airbag sensor assembly) ·
Forward recognition camera |
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
The lane departure alert system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Lane departure alert system DTC C1AA4 or C1AA5 may be stored due to a malfunction in the vehicle stability control system. Therefore it is necessary to check for and troubleshoot vehicle stability control system DTCs first.
Check for DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Vehicle stability control system DTCs are not output | A |
| Vehicle stability control system DTCs are output | B |
A
B
Clear the DTCs.
Perform the following procedure.
If the following procedure is not performed, the previously output DTC cannot be detected.
Turn the engine switch on (IG) and wait 2 seconds or more.
Drive the vehicle at a speed of 1 km/h or 1 mph or more for 5 seconds or more.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1AA4 and C1AA5 are not output | A |
| DTC C1AA4 or C1AA5 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Replace the forward recognition camera.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL
Perform forward recognition camera adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Perform the following procedure.
If the following procedure is not performed, the previously output DTC cannot be detected.
Turn the engine switch on (IG) and wait 2 seconds or more.
Drive the vehicle at a speed of 1 km/h or 1 mph or more for 5 seconds or more.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1AA4 and C1AA5 are not output | A |
| DTC C1AA4 or C1AA5 is output | B |
A
B