Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › from 2016.11
RM3160E _58 Vehicle Interior _060169 PRE-COLLISION _0296083 PRE-COLLISION SYSTEM C

PRE-COLLISION  PRE-COLLISION SYSTEM  C1A4A  Skid Control Buzzer Circuit  


DESCRIPTION

The driving support ECU assembly operates the pre-collision warning by sending a buzzer request signal to the skid control buzzer assembly.

If the driving support ECU assembly detects a malfunction in the skid control buzzer assembly circuit, it will store DTC C1A4A.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A4A Skid Control Buzzer Circuit When the engine switch is on (IG) and the pre-collision warning is operating, either of the following conditions is met:
·

A buzzer request signal is sent to the skid control buzzer assembly but the buzzer does not sound for 1 second or more.

·

A buzzer request signal is not sent to the skid control buzzer assembly but the buzzer sounds for 1 second or more.


·

Skid control buzzer assembly

·

Driving support ECU assembly

·

Wire harness or connector



WIRING DIAGRAM

B456420E10
0.146,0.688 1.688,0.927 1.542,0.24 10 false from IG1 NO. 3 Relay 2.208,0.844 2.99,1.063 0.781,0.219 10 false IG1 NO. 3 3.385,1.208 4.625,1.646 1.24,0.438 10 false Skid Control Buzzer Assembly 3.396,1.042 3.75,1.25 0.354,0.208 10 false A59 3.563,0.698 3.917,0.906 0.354,0.208 10 false IG1 4.24,0.698 4.594,0.906 0.354,0.208 10 false BZ 3.396,0.583 3.563,0.76 0.167,0.177 10 false 2 4.49,0.573 4.656,0.75 0.167,0.177 10 false 1 5.521,0.698 5.875,0.906 0.354,0.208 10 false BZ 5.354,0.573 5.521,0.75 0.167,0.177 10 false 3 5.052,1.948 5.521,2.167 0.469,0.219 10 false F128 5.042,2.104 7.01,2.323 1.969,0.219 10 false Driving Support ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.


Body Electrical > Pre-Collision 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Collision Alarm Buzzer Skid control buzzer assembly ON / OFF Test possible with engine switch on (IG), vehicle stopped
Body Electrical > Pre-Collision 2 > Active Test
Tester Display
PCS Collision Alarm Buzzer
50004 220 5

c.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

B

2.CHECK TERMINAL VOLTAGE
2.CHECK TERMINAL VOLTAGE
a.
B443157C13
1.5,0.177 1.906,0.438 0.406,0.26 1.99,1.333 2.5,1.156 true 0.188,0.156 0.5,0.313 0.313,0.156 10 false *a 1.583,0.229 2.042,0.427 0.458,0.198 10 false A59 2.552,1.063 3.01,1.26 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to Skid Control Buzzer Assembly)


Disconnect the A59 skid control buzzer assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A59-2 (IG1) - Body ground Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V



c.

Connect the A59 skid control buzzer assembly connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - BATTERY)

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the A59 skid control buzzer assembly connector.


b.

Disconnect the F128 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A59-1 (BZ) - F128-3 (BZ) Always Below 1 Ω
A59-1 (BZ) or F128-3 (BZ) - Body ground Always 10 kΩ or higher



d.

Connect the F128 driving support ECU assembly connector.


e.

Connect the A59 skid control buzzer assembly connector.


Result:
Proceed to
OK
NG



OK

6.INSPECT SKID CONTROL BUZZER ASSEMBLY (CONFIRM BUZZER OPERATION)

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
4.REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
5.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.


Body Electrical > Pre-Collision 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Collision Alarm Buzzer Skid control buzzer assembly ON / OFF Test possible with engine switch on (IG), vehicle stopped
Body Electrical > Pre-Collision 2 > Active Test
Tester Display
PCS Collision Alarm Buzzer
50004 220 5

c.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

END

B

6.INSPECT SKID CONTROL BUZZER ASSEMBLY (CONFIRM BUZZER OPERATION)
6.INSPECT SKID CONTROL BUZZER ASSEMBLY (CONFIRM BUZZER OPERATION)
a.

Turn the engine switch on (IG).


b.

Check if the skid control buzzer assembly is sounding.


Result:
Result Proceed to
The skid control buzzer assembly does not sound when the engine switch is on (IG) A
The skid control buzzer assembly sounds continuously when the engine switch is on (IG) B



A

7.INSPECT SKID CONTROL BUZZER ASSEMBLY (UNIT INSPECTION)

B

8.REPLACE SKID CONTROL BUZZER ASSEMBLY
7.INSPECT SKID CONTROL BUZZER ASSEMBLY (UNIT INSPECTION)
a.

Remove the skid control buzzer assembly.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM WARNING BUZZER>REMOVAL


b.

Inspect the skid control buzzer assembly.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM WARNING BUZZER>INSPECTION


Result:
Result Proceed to
Skid control buzzer assembly is abnormal A
Skid control buzzer assembly is normal B



A

8.REPLACE SKID CONTROL BUZZER ASSEMBLY

B

9.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
8.REPLACE SKID CONTROL BUZZER ASSEMBLY
a.

Replace the skid control buzzer assembly.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM WARNING BUZZER>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
9.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.


Body Electrical > Pre-Collision 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Collision Alarm Buzzer Skid control buzzer assembly ON / OFF Test possible with engine switch on (IG), vehicle stopped
Body Electrical > Pre-Collision 2 > Active Test
Tester Display
PCS Collision Alarm Buzzer
50004 220 5

c.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

END

B