Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019702 PARK ASSIST / MONITORING _0109515 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB2  Short to GND in Outer Mirror Indicator(Master)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects a short to ground in the outer rear view mirror indicator LH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB2 Short to GND in Outer Mirror Indicator(Master)
Both of the following conditions are met:
·

The blind spot monitor system is on


·

The current that is sent from the blind spot monitor sensor to the indicator is above a specified level for a specified period of time


·

Outer mirror LH

·

Outer rear view mirror assembly LH

·

Wire harness or connector

·

Blind spot monitor sensor LH

·

Outer mirror control ECU assembly LH



WIRING DIAGRAM

E359607E01
2.875,1.354 3.333,1.552 0.458,0.198 10 false z10 2.885,1.823 3.344,2.021 0.458,0.198 10 false z10 4.594,1.354 5.052,1.552 0.458,0.198 10 false I2 4.594,1.833 5.052,2.031 0.458,0.198 10 false I2 3.26,1.354 3.719,1.552 0.458,0.198 10 false BSL+ 4.031,1.344 4.49,1.542 0.458,0.198 10 false BDSL 4.104,1.833 4.563,2.031 0.458,0.198 10 false GND 3.26,1.823 3.583,2.021 0.323,0.198 10 false - 5.969,1.365 6.427,1.563 0.458,0.198 10 false OMIL 0.24,2.146 0.75,2.323 0.51,0.177 10 false IND1 0.24,2.292 1.573,2.49 1.333,0.198 10 false Outer Mirror LH 0.24,2.49 2.396,2.865 2.156,0.375 10 false (Outer Rear View Mirror Assembly LH) 3.24,3.365 4.521,3.74 1.281,0.375 10 false Outer Mirror Control ECU Assembly LH 5.917,3.5 7.115,3.917 1.198,0.417 10 false Blind Spot Monitor Sensor LH 5.917,3.344 6.375,3.542 0.458,0.198 10 false M31 1.552,1.271 1.708,1.469 0.156,0.198 10 false 2 1.552,1.74 1.708,1.938 0.156,0.198 10 false 1 2.927,1.156 3.083,1.354 0.156,0.198 10 false 8 2.896,1.635 3.104,1.833 0.208,0.198 10 false 12 4.552,1.156 4.771,1.354 0.219,0.198 10 false 13 4.604,1.635 4.76,1.833 0.156,0.198 10 false 7 5.792,1.25 6.01,1.448 0.219,0.198 10 false 4 1.396,1.354 1.552,1.552 0.156,0.198 10 false + 1.417,1.813 1.573,2.01 0.156,0.198 10 false - 0.156,3.375 2.646,3.646 2.49,0.271 10 false Outer Rear View Mirror Assembly LH


CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Clear DTCs
50002 313

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER MIRROR CONTROL ECU ASSEMBLY LH)
2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER MIRROR CONTROL ECU ASSEMBLY LH)
a.

Disconnect the M31 blind spot monitor sensor LH connector.


b.

Disconnect the I2 outer mirror control ECU assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Always
M31-4 (OMIL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
a.

Disconnect the z10 outer mirror control ECU assembly LH connector.


b.

Disconnect the IND1 outer mirror LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z10-8 (BSL+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

4.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY LH
a.
E233744C90
2.219,0.208 2.646,0.469 0.427,0.26 2.146,1.26 2.365,1.708 false 1.958,1.115 1.667,1.708 false 2.375,0.26 2.677,0.458 0.302,0.198 10 false I2 2.229,1.708 2.708,1.906 0.479,0.198 10 false BDSL 0.094,0.031 0.292,0.229 0.198,0.198 10 false *a 1.49,1.708 1.969,1.906 0.479,0.198 10 false GND
*a Component without harness connected (Outer Mirror Control ECU Assembly LH )


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I2-13 (BDSL) - I2-7 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT OUTER MIRROR LH

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

5.INSPECT OUTER MIRROR LH

b.

Inspect the outer rear view mirror indicator LH on the outer mirror LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION


Result:
Proceed to
OK
NG



OK

NG