Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019702 PARK ASSIST / MONITORING _0109515 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1ABE  Short to GND or Open in Buzzer  


DESCRIPTION

DTC C1ABE is stored when the blind spot monitor sensor RH detects a short to ground or open in the rear crossing traffic alert buzzer (blind spot monitor buzzer) circuit.


DTC No. Detection Item DTC Detection Condition Trouble Area
C1ABE Short to GND or Open in Buzzer
Both of the following conditions are met:
·

The blind spot monitor system is on

·

The blind spot monitor sensor is not sounding the buzzer but the buzzer receives voltage below a specified level for a specified period of time.


·

Blind spot monitor sensor RH

·

Rear crossing traffic alert buzzer (blind spot monitor buzzer)

·

Wire harness or connector



WIRING DIAGRAM

E254403E75
0.167,1.01 1.573,1.208 1.406,0.198 10 false from IG1-NO. 3 Relay 3.5,1 3.792,1.198 0.292,0.198 10 false BZP 3.094,1.302 3.438,1.5 0.344,0.198 10 false M44 3.083,1.479 5.25,1.885 2.167,0.406 10 false Rear Crossing Traffic Alert Buzzer (Blind Spot Monitor Buzzer) 5.615,1.927 5.906,2.125 0.292,0.198 10 false L23 5.615,2.083 6.813,2.448 1.198,0.365 10 false Blind Spot Monitor Sensor RH 4.333,1.01 4.667,1.208 0.333,0.198 10 false BZN 3.333,0.906 3.479,1.083 0.146,0.177 10 false 1 5.646,1.021 5.979,1.219 0.333,0.198 10 false BUZ 5.469,0.917 5.615,1.094 0.146,0.177 10 false 3 4.677,0.917 4.823,1.094 0.146,0.177 10 false 2 2.24,1.167 2.75,1.375 0.51,0.208 10 false DSS-IG

CAUTION / NOTICE / HINT

NOTICE:
·

When checking for DTCs, make sure that the blind spot monitor system is turned on.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON.


c.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (REAR CROSSING TRAFFIC ALERT BUZZER - BATTERY AND BLIND SPOT MONITOR SENSOR RH)
2.CHECK HARNESS AND CONNECTOR (REAR CROSSING TRAFFIC ALERT BUZZER - BATTERY AND BLIND SPOT MONITOR SENSOR RH)
a.

Disconnect the M44 rear crossing traffic alert buzzer (blind spot monitor buzzer) connector.


b.

Disconnect the L23 blind spot monitor sensor RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M44-2 (BZN) - L23-3 (BUZ) Always Below 1 Ω
M44-2 (BZN) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M44-1 (BZP) - Body ground Ignition Switch ON 11 to 14 V
M44-1 (BZP) - Body ground Ignition Switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.REPLACE REAR CROSSING TRAFFIC ALERT BUZZER (BLIND SPOT MONITOR BUZZER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE REAR CROSSING TRAFFIC ALERT BUZZER (BLIND SPOT MONITOR BUZZER)
a.

Replace the rear crossing traffic alert buzzer (blind spot monitor buzzer).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>REAR CROSSING TRAFFIC ALERT BUZZER>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC
4.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG