Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019702 PARK ASSIST / MONITORING _0109515 BLIND SPOT MONITOR SYSTEM J

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  Buzzer does not Sound  


WIRING DIAGRAM

E254403E76
0.156,1.021 1.563,1.219 1.406,0.198 10 false from IG1-NO. 3 Relay 3.073,1.313 3.417,1.51 0.344,0.198 10 false M44 3.073,1.479 5.198,1.833 2.125,0.354 10 false Rear Crossing Traffic Alert Buzzer (Blind Spot Monitor Buzzer) 5.615,1.927 5.906,2.125 0.292,0.198 10 false L23 5.604,2.083 6.802,2.406 1.198,0.323 10 false Blind Spot Monitor Sensor RH 3.354,0.927 3.5,1.104 0.146,0.177 10 false 1 5.646,1.021 5.979,1.219 0.333,0.198 10 false BUZ 5.479,0.917 5.625,1.094 0.146,0.177 10 false 3 4.698,0.917 4.844,1.094 0.146,0.177 10 false 2 2.25,1.177 2.854,1.417 0.604,0.24 10 false DSS-IG 4.302,1.021 4.635,1.219 0.333,0.198 10 false BZN 3.51,1.01 3.844,1.208 0.333,0.198 10 false BZP

CAUTION / NOTICE / HINT

NOTICE:
·

When checking for DTCs, make sure that the blind spot monitor system is turned on.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK REAR CROSSING TRAFFIC ALERT BUZZER (BLIND SPOT MONITOR BUZZER)
a.

Check that the rear crossing traffic alert buzzer (blind pot monitor buzzer) sounds when the initial check is performed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>SYSTEM DESCRIPTION

OK:

Rear crossing traffic alert buzzer sounds



Result:
Proceed to
OK
NG



OK

NG

2.CHECK DTC
2.CHECK DTC
a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON.


c.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (REAR CROSSING TRAFFIC ALERT BUZZER - BLIND SPOT MONITOR SENSOR RH)

NG

3.CHECK HARNESS AND CONNECTOR (REAR CROSSING TRAFFIC ALERT BUZZER - BLIND SPOT MONITOR SENSOR RH)
a.

Disconnect the M44 buzzer (blind spot monitor buzzer) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M44-1 (BZP) - Body ground Ignition Switch ON 11 to 14 V
M44-2 (BZN) - Body ground Below 1 V
M44-2 (BZN) - M44-1 (BZP) Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (REAR CROSSING TRAFFIC ALERT BUZZER - BLIND SPOT MONITOR SENSOR RH AND BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (REAR CROSSING TRAFFIC ALERT BUZZER - BLIND SPOT MONITOR SENSOR RH AND BATTERY)
a.

Disconnect the M44 rear crossing traffic alert buzzer (blind spot monitor buzzer) connector.


b.

Disconnect the L23 blind spot monitor sensor RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M44-2 (BZN) - L23-3 (BUZ) Always Below 1 Ω
M44-2 (BZN) or L23-3 (BUZ) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M44-2 (BZN) or L23-3 (BUZ) - Body ground Ignition Switch ON Below 1 V
M44-1 (BZP) - Body ground Ignition Switch ON 11 to 14 V
M44-1 (BZP) - Body ground Ignition Switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR