Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › from 2016.11
RM3160E _52 Drivetrain _019727 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0109809 AUTOMATIC TRANSAXLE SYSTEM C

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0796  Pressure Control Solenoid "C" Performance (Shift Solenoid Valve SL3)  


SYSTEM DESCRIPTION

The ECM uses the vehicle speed signal and signals from the transmission speed sensors (NC, NT) to detect the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear).

The ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves and valve body.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0796 Pressure Control Solenoid "C" Performance (Shift Solenoid Valve SL3) The engine revs freely when 2nd or 6th gear is commanded (2-trip detection logic).
When the following is detected twice (2-trip detection logic):
·

When 1st gear is commanded, 2nd gear is engaged.


·

Shift solenoid valve SL3 remains open or closed.

·

Valve body is blocked.

·

Automatic transaxle (clutch, brake or gear etc.)


Comes on DTC stored

MONITOR DESCRIPTION

The ECM commands gear shifts by turning the shift solenoid valves on and off. According to the input shaft revolution (speed), intermediate (counter) shaft revolution (speed) and output shaft revolution (speed), the ECM detects the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear). When the gear commanded by the ECM and the actual gear are not the same, the ECM illuminates the MIL and stores a DTC.

PROCEDURE

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0796)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

e.

Read the DTCs using the GTS.

Result:
Result Proceed to
Only DTC P0796 is output A
P0796 and other DTCs are output B


HINT:

If a solenoid is stuck off, DTCs for several solenoids including the malfunctioning solenoid will be detected.




A

3.INSPECT SHIFT SOLENOID VALVE SL3

B

2.PERFORM ACTIVE TEST USING GTS
2.PERFORM ACTIVE TEST USING GTS
NOTICE:

This test should always be performed with at least 2 people.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on the GTS, perform the Active Test.

HINT:

Comparing the gear commanded by the Active Test with the actual gear enables confirmation of the problem.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART


Powertrain > Engine > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Control the Shift Position Operates the shift solenoid valves to allow gears to selected manually.
·

Press "→" button: Upshift occurs

·

Press "←" button: Downshift occurs


Can be used to check the operation of the shift solenoid valves.
Upshifts and downshifts should be performed consecutively. A 10-second interval is required between gear changes.
Do not downshift at high speeds.
Doing so will damage the automatic transaxle.
[Vehicle Condition]
50 km/h (30 mph) or less
Powertrain > Engine > Active Test
Tester Display
Control the Shift Position
50004 234 116
NOTICE:
·

This test can be conducted when the vehicle is stopped.

·

When shifting gears using the Active Test function, do not operate the accelerator pedal for 2 seconds before and after shifting gears.



HINT:

The gear commanded by the ECM is shown in the Data List / Shift Status display on the GTS.



h.

Check the vehicle speed and the gear when the engine speed is 1000 rpm.

HINT:

Because the torque converter clutch has not engaged, it may be difficult to obtain the speeds specified in 4th, 5th, and 6th gear, however a difference of speed should still be evident following each gear change.


Standard:
1st 2nd 3rd 4th 5th 6th
8 to 12 km/h (5 to 7.5 mph) 15 to 19 km/h (9.3 to 11.8 mph) 21 to 25 km/h (13.0 to 15.5 mph) 31 to 35 km/h (19.3 to 21.7 mph) 44 to 48 km/h (27.3 to 29.8 mph) 52 to 56 km/h (32.3 to 34.8 mph)



i.

Compare the ECM commanded gear and the actual gear.

Result:
Actual Gear during Malfunction ECM Commanded Gear Proceed to
1st 2nd 3rd 4th 5th 6th
Shift solenoid SL1 Stuck ON 1st 2nd 3rd 4th 4th 4th A
Stuck OFF N*1 N*1 N*1 N*1 5th 6th
Shift solenoid SL2 Stuck ON 4th 4th 4th 4th 5th 6th B
Stuck OFF 1st 2nd 3rd 1st N*1 N*1
Shift solenoid SL3 Stuck ON 2nd 2nd 3rd 4th 5th 6th C
Stuck OFF 1st 1st 3rd 4th 5th N*1
Shift solenoid SL4 Stuck ON*3 3rd 3rd 3rd 4th 5th 5th D
Stuck OFF 1st 2nd 1st 4th N*1 6th
Shift solenoid SLT Stuck ON N*2 N*2 N*2 N*2 N*2 N*2 E
Stuck OFF*3 1st 2nd 3rd 4th 5th 6th


HINT:
·

*1: Neutral

·

*2: If shift solenoid SLT is stuck on, the line pressure will be low. Therefore, the amount of torque that can be transmitted by each gear is lower than the normal limit. When the engine power exceeds this lowered limit, the engine speed will increase freely.

·

*3: When shift solenoid SLT is stuck off, gear shifting is normal.





A

GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE (SL1) PERFORMANCE DTC P0746)

B

GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE (SL2) PERFORMANCE DTC P0776)

C

3.INSPECT SHIFT SOLENOID VALVE SL3

D

GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE (SL4) PERFORMANCE DTC P2808)

E

GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE (SLT) PERFORMANCE DTC P2714)

3.INSPECT SHIFT SOLENOID VALVE SL3
a.
C201747C02
1.49,0.875 0.635,0.646 false 1.781,0.865 2.479,0.625 false 1.49,3.125 0.635,2.896 false 1.781,3.125 2.479,2.885 false 0.49,0.521 0.667,0.719 0.177,0.198 10 1 2.531,0.5 2.708,0.698 0.177,0.198 10 2 1.177,4.198 1.385,4.406 0.208,0.208 10 (-) 1.917,4.208 2.146,4.406 0.229,0.198 10 (+) 0.51,2.771 0.688,2.969 0.177,0.198 10 1 2.521,2.76 2.698,2.958 0.177,0.198 10 2 0.135,0.135 0.354,0.344 0.219,0.208 10 *1
*1 Shift Solenoid Valve SL3


Remove shift solenoid valve SL3.

When Not Using the Engine Support Bridge: Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY(When Not Using the Engine Support Bridge)>DISASSEMBLY

When Using the Engine Support Bridge: Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY(When Using the Engine Support Bridge)>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK:

There is no foreign matter on each valve and they operate smoothly.


Result:
Proceed to
OK
NG



OK

NG