Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER › from 2016.11
RM3160E _59 Vehicle Exterior _019724 EXTERIOR PANELS / TRIM _0109633 FRONT BUMPER A

EXTERIOR PANELS / TRIM  FRONT BUMPER  REMOVAL  


CAUTION / NOTICE / HINT

HINT:

When the front bumper is damaged or deformed due to an accident or contact with other objects, etc., or the bumper installation area on the body is repaired, it is necessary to perform millimeter wave radar sensor adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


PROCEDURE

Hide 1.REMOVE RADIATOR GRILLE ASSEMBLY

Hide 75086 2.DISCONNECT FRONT FENDER WHEEL OPENING MOULDING SUB-ASSEMBLY LH

a.
B461293C01
2.792,1.625 2.792,2.188 true 2.729,2.208 2.917,2.354 0.188,0.146 10 true *1 1.292,2.073 1.458,2.24 0.167,0.167 10 true *a
*1 Pin Hold Clip
*a 90°


Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.


b.

Remove the 2 screws.


c.

Remove the clip.


d.
B461294

Remove the clip.


e.
B463671C01
0.76,0.708 1.073,0.865 0.313,0.156 10 false *a
*a Push


Pull back the edge of the front fender liner LH and disengage the 4 claws by pushing the area indicated by the arrow in the illustration with a finger.

NOTICE:
·

Do not apply excessive force when pulling back the front fender liner LH.

·

To avoid damaging the claws, do not forcibly pull the front fender wheel opening moulding sub-assembly LH.




f.

Disengage the 2 clips and disconnect the front fender wheel opening moulding sub-assembly LH.


Hide 75085A 3.DISCONNECT FRONT FENDER WHEEL OPENING MOULDING SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 4.REMOVE FRONT BUMPER ASSEMBLY

a.
B461296C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the front bumper assembly as shown in the illustration.


b.
B461297

Remove the 8 screws.


c.
B461298C01
2.583,3.323 3,2.906 true 3.021,2.823 3.219,2.979 0.198,0.156 10 true *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, disengage the claw as shown in the illustration.

HINT:

Use the same procedure for the RH side and LH side.



d.
B461300

Disengage the 3 claws as shown in the illustration.

HINT:

Use the same procedure for the RH side and LH side.



e.
B461302C01
2.531,1.802 2.896,2.208 2.896,2.208 2.073,1.615 true 2.927,2.115 3.177,2.323 0.25,0.208 12 true *A
*A w/ TOYOTA Parking Assist-sensor System (for 6 Sensor Type)


Pull back the side of the front bumper assembly, disengage each clamp and disconnect each connector.

NOTICE:

Do not apply excessive force when pulling back the front bumper assembly.


HINT:

Use the same procedure for the RH side and LH side.



f.

w/ Panoramic View Monitor System:

i.
B462665

Disconnect the connector.



g.
B461299

Remove the 3 clips and front bumper assembly as shown in the illustration.