Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS) › from 2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0296316 DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS) C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS)  C1A0A  Front Radar Sensor Region Code Mismatch  


DESCRIPTION

The driving support ECU assembly uses the millimeter wave radar sensor assembly to detect objects in front of the vehicle.

When the destination information in the millimeter wave radar sensor assembly and driving support ECU assembly do not match, DTC C1A0A is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A0A Front Radar Sensor Region Code Mismatch When the engine switch is on (IG) and the dynamic radar cruise control system is operating, the destination information in the driving support ECU assembly and millimeter wave radar sensor assembly do not match for approximately 1.4 seconds or more.
·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly



CAUTION / NOTICE / HINT

NOTICE:
·

Check that the millimeter wave radar sensor assembly has not been replaced with one from another vehicle.

·

When replacing the driving support ECU assembly, make sure to replace it with a new one. If a device which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle, and as a result, a DTC may be stored.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTC (RADAR CRUISE 2)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS)>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Clear DTCs
50002 197

b.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the following conditions are not met, the system cannot detect the malfunction.

1.

Turn the engine switch on (IG).

2.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON-OFF button).

3.

Wait for 2 seconds or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS)>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Trouble Codes
50001 197

Result:
Result Proceed to
DTC C1A0A is not output A
DTC C1A0A is output B



A

B

2.REPLACE DRIVING SUPPORT ECU ASSEMBLY
2.REPLACE DRIVING SUPPORT ECU ASSEMBLY

Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC (RADAR CRUISE 2)
3.CHECK FOR DTC (RADAR CRUISE 2)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS)>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Clear DTCs
50002 197

b.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the following conditions are not met, the system cannot detect the malfunction.

1.

Turn the engine switch on (IG).

2.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON-OFF button).

3.

Wait for 2 seconds or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS)>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Trouble Codes
50001 197

Result:
Result Proceed to
DTC C1A0A is not output A
DTC C1A0A is output B



A

END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)

B

4.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
4.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly with a new one.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)