The driving support ECU assembly sends vehicle speed and vehicle condition information to the millimeter wave radar sensor assembly. The millimeter wave radar sensor assembly then sends information on the presence, distance, and relative speed of objects in front of the vehicle to the driving support ECU assembly. The driving support ECU assembly sends this information to the ECM and the ECM operates the dynamic radar cruise control system.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| U0235 | Lost Communication with Cruise Control Front Distance Range Sensor | ·
While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, a communication error between the millimeter wave radar sensor assembly and the driving support ECU assembly is detected for approximately 1 second. |
·
Millimeter wave radar sensor assembly ·
Driving support ECU assembly ·
Harness or connector |
| U1104 | Lost Communication with Driving Support ECU | ·
While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, a communication error between the driving support ECU assembly and the millimeter wave radar sensor assembly is detected for approximately 1 second. |
·
Millimeter wave radar sensor assembly ·
Driving support ECU assembly ·
Harness or connector |
Inspect the fuses for circuits related to this system before performing the following procedure.
When replacing the driving support ECU assembly, make sure to replace it with a new one. If a device which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle, and as a result, a DTC may be stored.
When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
Using the GTS, check if the CAN communication system is functioning normally.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output | OK |
| CAN communication system DTCs are output | NG |
OK
NG
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the F128 driving support ECU assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F128-7 (B) - Body ground | Engine switch on (IG) | 11 to 14 V |
| F128-7 (B) - Body ground | Engine switch off | Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F128-28 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly) |
Disconnect the A81 millimeter wave radar sensor assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A81-8 (IGB) - Body ground | Engine switch on (IG) | 11 to 14 V |
| A81-8 (IGB) - Body ground | Engine switch off | Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A81-1 (SGND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F128 driving support ECU assembly connector.
Disconnect the A81 millimeter wave radar sensor assembly connector.
Disconnect the S18 forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F128-8 (CA1P) - A81-5 (CA1P) | Always | Below 1 Ω |
| F128-9 (CA1N) - A81-6 (CA1N) | Always | Below 1 Ω |
| F128-8 (CA1P) or A81-5 (CA1P) - Body ground | Always | 10 kΩ or higher |
| F128-9 (CA1N) or A81-6 (CA1N) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the millimeter wave radar sensor assembly with a new one.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL
Perform millimeter wave radar sensor assembly adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Perform the following to make sure that the DTC detection conditions are met.
If the following conditions are not met, the system cannot detect the malfunction.
Turn the engine switch on (IG).
Turn the dynamic radar cruise control system on using the cruise control main switch (ON-OFF button).
Drive the vehicle at 36 km/h (22 mph) or more for 1 second or more.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC U0235 and U1104 are not output | A |
| DTC U0235 or U1104 is output | B |
A
B
for LHD: Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU(for LHD)>COMPONENTS
for RHD: Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU(for RHD)>COMPONENTS