Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS) › from 2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0296316 DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS) J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS)  Cruise Control Switch Circuit  


DESCRIPTION

The cruise control main switch is used to turn the dynamic radar cruise control system on and off, as well as operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP and CANCEL.

The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCEL) functions are operated with the same switch. The cruise control main switch contains momentary type contacts for each function. The contacts close only while the cruise control main switch is being operated in the direction of the relative function arrow, and open when the cruise control main switch is released. The voltage at the terminal of the ECM changes as each of the different contacts open or close. The ECM reads this voltage and controls the SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL functions accordingly.

·

Vehicle-to-vehicle distance control mode is selected by default when the dynamic radar cruise control system is turned on using the cruise control main switch (ON-OFF button).

·

The operation of constant speed control mode is the same as that for a conventional cruise control system.


WIRING DIAGRAM

A369504E75
6.542,2.781 6.99,3 0.448,0.219 10 false ECM 4.615,2.563 5.688,2.917 1.073,0.354 10 false Spiral Cable Sub-assembly 3.469,2.573 4.385,2.948 0.917,0.375 10 false Cruise Control Switch Wire 0.792,2.594 2.521,2.813 1.729,0.219 10 false Cruise Control Main Switch 0.448,1.438 1.365,1.635 0.917,0.198 10 false CANCEL 1.219,1.427 1.833,1.625 0.615,0.198 10 false -SET 1.875,1.427 2.49,1.625 0.615,0.198 10 false +RES 2.51,1.427 3.427,1.625 0.917,0.198 10 false ON-OFF 2.771,0.771 3.229,0.969 0.458,0.198 10 false CCS 4.906,0.792 5.365,0.99 0.458,0.198 10 false CCS 6.385,0.875 6.844,1.073 0.458,0.198 10 false CCS 4.906,1.99 5.365,2.188 0.458,0.198 10 false ECC 2.75,1.979 3.208,2.177 0.458,0.198 10 false ECC 4.417,0.875 4.729,1.073 0.313,0.198 10 false z8 3.26,0.875 3.573,1.073 0.313,0.198 10 false A 5.521,0.875 5.958,1.083 0.438,0.208 10 false F61 6.375,2.594 6.833,2.792 0.458,0.198 10 false A43 6.156,0.76 6.49,1.156 0.333,0.396 10 false 41 5.594,1.865 5.75,2.063 0.156,0.198 10 false 2 5.604,0.667 5.76,0.865 0.156,0.198 10 false 1 4.406,0.667 4.646,0.865 0.24,0.198 10 false 3 3.26,0.656 3.417,0.854 0.156,0.198 10 false 3 4.427,1.854 4.583,2.052 0.156,0.198 10 false 4 3.26,1.865 3.417,2.063 0.156,0.198 10 false 1 3.75,0.781 4.208,0.979 0.458,0.198 10 false CCS 3.75,1.99 4.208,2.188 0.458,0.198 10 false ECC 3.26,2.073 3.573,2.271 0.313,0.198 10 false A 5.521,2.073 5.958,2.281 0.438,0.208 10 false F61 4.417,2.083 4.729,2.281 0.313,0.198 10 false z8

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Radar Cruise 1 / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Radar Cruise1 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Cancel Switch CANCEL switch status ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
-SET Switch -SET switch status ON or OFF ON: -SET switch on
OFF: -SET switch off
-
+RES Switch +RES switch status ON or OFF ON: +RES switch on
OFF: +RES switch off
-
Cruise Main Switch Operation Condition Cruise control main switch (ON-OFF button) status ON or OFF ON: Cruise control main switch (ON-OFF button) pushed
OFF: Cruise control main switch (ON-OFF button) not pushed
-
Powertrain > Radar Cruise1 > Data List
Tester Display
Cancel Switch
-SET Switch
+RES Switch
Cruise Main Switch Operation Condition
50003 374 18,19,20,41
OK:

The Data List items shown in the table change according to the operation of the cruise control main switch.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT CRUISE CONTROL MAIN SWITCH
2.INSPECT CRUISE CONTROL MAIN SWITCH
a.

Remove the cruise control main switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>REMOVAL


b.

Inspect the cruise control main switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK CRUISE CONTROL SWITCH WIRE

NG

3.CHECK CRUISE CONTROL SWITCH WIRE
a.
A315700C13
1.302,0.385 1.708,0.667 0.406,0.281 1.271,2.885 1.677,3.167 0.406,0.281 0.781,4.344 1.198,3.927 true 0.948,2.271 1.365,1.854 true 2.042,2.26 1.635,1.854 true 2.052,4.323 1.646,3.917 true 0.396,0.688 0.708,0.906 0.313,0.219 10 false *a 0.5,3.104 0.813,3.302 0.313,0.198 10 false *b 1.427,0.448 1.74,0.646 0.313,0.198 10 false z8 1.427,2.948 1.74,3.146 0.313,0.198 10 false A 0.813,2.281 1.271,2.479 0.458,0.198 10 false CCS 1.938,4.354 2.396,4.552 0.458,0.198 10 false CCS 0.604,4.354 1.063,4.552 0.458,0.198 10 false ECC 1.896,2.281 2.354,2.479 0.458,0.198 10 false ECC
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)
*b Front view of wire harness connector
(to Cruise Control Main Switch)


Remove the cruise control switch wire.

Click hereSteering>STEERING COLUMN>STEERING WHEEL>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z8-3 (CCS) - A-3 (CCS) Always Below 1 Ω
z8-4 (ECC) - A-1 (ECC) Always Below 1 Ω
z8-3 (CCS) or A-3 (CCS) - Body ground Always 10 kΩ or higher
z8-4 (ECC) or A-1 (ECC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE CRUISE CONTROL SWITCH WIRE

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)

NG

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)
a.

Disconnect the F61 spiral cable sub-assembly.


b.

Disconnect the A43 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F61-1 (CCS) - A43-41 (CCS) Always Below 1 Ω
F61-2 (ECC) - Body ground Always Below 1 Ω
F61-1 (CCS) or A43-41 (CCS) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK A
NG B



A

B

REPAIR OR REPLACE HARNESS OR CONNECTOR