The purpose of the stop light switch signal circuit is to prevent the engine from stalling when the brakes are suddenly applied while driving in the lock-up condition.
When the brake pedal is depressed, the stop light switch assembly sends a signal to the ECM. The ECM then cancels the operation of the lock-up clutch while braking is in progress.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P070312 | Brake Switch "B" Circuit Short to Battery | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.
The ignition switch is ON and battery voltage is 8 V or more. 2.
The stop light switch remains on. 3.
The vehicle is driven in a GO (30 km/h (19 mph) or more) and STOP (less than 3 km/h (2 mph)) pattern 5 times 4.
2-trip detection logic |
·
Stop light switch assembly ·
Short in stop light switch signal circuit ·
ECM |
Comes on | DTC stored | SAE Code:
P0724 |
This DTC indicates that the stop light switch is remaining on. When the stop light switch remains on during GO and STOP driving, the ECM interprets this as a malfunction of the stop light switch assembly, illuminates the MIL and stores this DTC. The vehicle must GO (30 km/h (19 mph) or more) and STOP (less than 3 km/h (2 mph)) 5 times for 2 consecutive driving cycles in order for this DTC to be stored.
Refer to SFI system DTC P05042B.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>P05042B
Inspect the fuses for circuits related to this system before performing the following procedure.
Perform registration and/or initialization when parts related to the automatic transaxle are replaced.
Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION
After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Repeat the following procedure 5 times:
Perform the following procedure while strictly observing all traffic laws and speed limits.
Accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (2 mph) or less.
Turn the ignition switch off.
Perform step (1) again.
Check for DTCs again.
Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR
DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Data List / Stop Light SW.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light SW | Stop light switch status | ON or OFF | ·
ON: Brake pedal depressed ·
OFF: Brake pedal released |
- |
| Tester Display |
|---|
| Stop Light SW |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Data List / Stop Light SW.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light SW | Stop light switch status | ON or OFF | ·
ON: Brake pedal depressed ·
OFF: Brake pedal released |
- |
| Tester Display |
|---|
| Stop Light SW |
| Result | Proceed to |
|---|---|
| Data List value is normal | A |
| Data List value is not normal | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Check the stop light switch assembly installation condition.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION
Stop light switch assembly is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A43 ECM connector.
| *a | Brake pedal depressed | *b | Brake Pedal Released |
| *c | Front view of wire harness connector
(to ECM) |
- | - |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A43-27 (STP) - Body ground | Brake pedal released | Below 1.5 V |
| Brake pedal depressed | 7.5 to 14 V |
If there is a short in the STP terminal circuit, there may be a malfunction in the circuit of a connected ECU.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ECM>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>REGISTRATION