Refer to DTC P074011.
Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>P074011
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P074015 | Torque Converter Clutch Circuit Short to Battery or Open | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.
Solenoid (SL) valve is operated 2.
Solenoid (SL) valve circuit is short to +B or open 3.
Malfunction status occurs 1 time per trip 4.
2-trip detection logic |
·
Solenoid (SL) valve ·
Transmission wire ·
Harness and connector ·
ECM |
Comes on | DTC stored | SAE Code:
P2770 |
Based on the signals from the throttle position sensor, the air flow meter and the crankshaft position sensor, the ECM sends a signal to solenoid (SL) valve to regulate the hydraulic pressure and provide smoother torque converter engagement. Solenoid (SL) valve responds to commands from the ECM. The valve controls the lock-up relay valve to perform the torque-converter lock-up function. If the ECM detects an open or short to +B in the solenoid (SL) valve circuit, it will illuminate the MIL and store the DTC.
Refer to DTC P074011.
Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>P074011
Perform registration and/or initialization when parts related to the automatic transaxle are replaced.
Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION
After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Perform the D Position Shift Test inspection in Road Test.
Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>ROAD TEST
Turn the ignition switch off.
Perform step (1) again.
Check for DTCs again.
Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR
| *a | Component without harness connected
(Transmission Wire) |
Disconnect the C85 transmission wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 13 (SL) - Body ground | 20°C (68°F) | 11 to 15 Ω |
| 13 (SL) - Other terminals | Always | 10 kΩ or higher |
Connect the C85 transmission wire connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C1 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C1-62 (SL) - Body ground | 20°C (68°F) | 11 to 15 Ω |
| C1-62 (SL) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ECM>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>REGISTRATION
| *1 | Solenoid (SL) Valve |
Remove the solenoid (SL) valve.
Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Solenoid (SL) valve connector terminal - Solenoid (SL) valve body | 20°C (68°F) | 11 to 15 Ω |
Connect a positive (+) lead from the battery to the terminal of the solenoid valve connector, and a negative (-) lead to the solenoid body. Check that the valve moves and makes an operating sound.
Valve moves and makes an operating sound.
| Proceed to |
|---|
| OK |
| NG |
OK
When Not Using the Engine Support Bridge: Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>TRANSMISSION WIRE(When Not Using the Engine Support Bridge)>COMPONENTS
When Using the Engine Support Bridge: Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>TRANSMISSION WIRE(When Using the Engine Support Bridge)>COMPONENTS
NG