The ECM uses signals from the throttle position sensor, mass air flow meter, transmission revolution sensor (NT), transmission revolution sensor (NC) and crankshaft position sensor to help determine the engagement timing of the lock-up clutch. The ECM monitors the engagement of the clutch using the transmission revolution sensor (NT), transmission revolution sensor (NC) and crankshaft position sensor.
Then the ECM compares the engagement condition of the lock-up clutch with the lock-up schedule in the ECM memory to detect solenoid (SL) valve, transmission valve body assembly and torque converter assembly mechanical problems.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P07407E | Torque Converter Clutch Actuator Stuck On | 1. Diagnosis Condition, 2. Malfunction Status, 3. Malfunction Time, 4. Other
1.
Engine coolant temperature is 40°C (104°F) or higher, ATF temperature is -10°C (14°F) or higher, and the vehicle is being driven with the shift lever in D (no malfunctions are detected in the solenoid (SL1, SL2, SL3, SL4, SL5, SL6, SL, SLU and SLT) valves, transmission revolution sensors (NT, NC), coolant temperature sensor, oil temperature sensor, knock control sensor, electronic throttle or CAN2) 2.
When the ECM commands the solenoid (SL) valve OFF, the difference between the turbine speed (NT) and engine speed (NE) is 70 rpm or more. 3.
Malfunction status continues for 3.5 seconds or more 4.
2-trip detection logic |
·
Solenoid (SL) valve remains closed ·
Transmission wire ·
Transmission valve body assembly is blocked ·
Torque converter assembly ·
Automatic transaxle assembly (clutch, brake, gear etc.) ·
Line pressure is too low |
Comes on | DTC stored | SAE Code:
P0741 |
Torque converter lock-up is controlled by the ECM based on the transmission revolution sensor (NT), transmission revolution sensor (NC), engine speed, engine load, engine temperature, vehicle speed, transmission fluid temperature, and gear selection. The ECM determines the lock-up status of the torque converter by comparing the engine speed (NE) to the input turbine speed (NT). The ECM calculates the actual transmission gear by comparing the input turbine speed (NT) to the output shaft speed (NC). When certain conditions are met, the ECM requests "lock-up" by cutting control voltage to the solenoid (SL) valve. When the solenoid (SL) valve is turned off, pressure is applied to the lock-up relay valve and the torque converter is locked.
If the ECM detects no lock-up after lock-up has been requested or if it detects lock-up when it is not requested, the ECM interprets this as a fault in the solenoid (SL) valve or lock-up system performance. The ECM will illuminate the MIL and store the DTC.
Example:
When any of the following is met, the system judges it as a malfunction.
There is a difference in rotation speed between the input side (engine speed) and output side (input turbine speed) of the torque converter when the ECM commands lock-up.
(Engine speed is at least 70 rpm more than the input turbine speed.)
There is no difference in rotation speed between the input side (engine speed) and output side (input turbine speed) of the torque converter when the ECM commands lock-up off.
(The difference between engine speed and input turbine speed is less than 35 rpm.)
Refer to DTC P074011.
Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>P074011
Perform registration and/or initialization when parts related to the automatic transaxle are replaced.
Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION
After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Perform the Lock-up Function inspection in Road Test.
Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>ROAD TEST
Turn the ignition switch off.
Perform step (1) again.
Check for DTCs again.
Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Activate the Lock Up Solenoid | Operates the solenoid (SLU and SL) valve to control the automatic transaxle lock-up condition | ON or OFF | Can be used to check the operation of the solenoid (SLU and SL) valve.
[Vehicle Condition] Vehicle speed: 60 km/h (36 mph) or more |
| Tester Display |
|---|
| Activate the Lock Up Solenoid |
This test can be conducted when the vehicle speed is 60 km/h (36 mph) or more.
Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.
When changing the accelerator pedal opening angle while driving, if the engine speed does not change, lock-up is on.
Slowly release the accelerator pedal in order to decelerate, but do not fully release the pedal. (Fully releasing the pedal will close the throttle valve and lock-up may be prohibited.)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Trouble Codes.
Read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| Only DTC P07407E is output | A |
| DTC P07407E and other DTCs are output | B |
If any other codes besides P07407E are output, perform the troubleshooting for those DTCs first.
A
B
| *a | Component without harness connected
(Transmission Wire) |
Disconnect the C85 transmission wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 13 (SL) - Body ground | 20°C (68°F) | 11 to 15 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Solenoid (SL) Valve |
Remove the solenoid (SL) valve.
Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY
Connect a positive (+) lead from the battery to the terminal of the solenoid valve connector, and a negative (-) lead to the solenoid body. Check that the valve moves and makes an operating sound.
Valve moves and makes an operating sound.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the transmission valve body assembly.
Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>REMOVAL
There is no foreign matter on each valve and they operate smoothly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the torque converter assembly.
Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER AND DRIVE PLATE>INSPECTION
The torque converter assembly is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
When Not Using the Engine Support Bridge: Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge)>COMPONENTS
When Using the Engine Support Bridge: Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge)>COMPONENTS
Repair or replace the automatic transaxle assembly.
When Not Using the Engine Support Bridge: Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge)>COMPONENTS
When Using the Engine Support Bridge: Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge)>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>REGISTRATION
| *1 | Solenoid (SL) Valve |
Remove the solenoid (SL) valve.
Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Solenoid (SL) valve connector terminal - Solenoid (SL) valve body | 20°C (68°F) | 11 to 15 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
When Not Using the Engine Support Bridge: Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TRANSMISSION WIRE(When Not Using the Engine Support Bridge)>COMPONENTS
When Using the Engine Support Bridge: Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TRANSMISSION WIRE(When Using the Engine Support Bridge)>COMPONENTS
NG