Home › Drivetrain › UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › from 2017.10
RM3160E _52 Drivetrain _060165 UA80F AUTOMATIC TRANSMISSION / TRANSAXLE _0303922 AUTOMATIC TRANSAXLE SYSTEM C

UA80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P079112  Intermediate Shaft Speed Sensor "A" Circuit Short to Battery  P079114  Intermediate Shaft Speed Sensor "A" Circuit Short to Ground or Open  P079131  Intermediate Shaft Speed Sensor "A" No Signal  


DESCRIPTION

The transmission revolution sensor (NC) detects the rotation speed of the counter gear which shows the output shaft speed of automatic transaxle assembly.

Based on the transmission revolution sensor (NC) signal and the transmission revolution sensor (NT) signal, the ECM controls engine torque and shift timing.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P079112 Intermediate Shaft Speed Sensor "A" Circuit Short to Battery 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The battery voltage is 8 V or more, the ignition switch is ON and the starter is off.

2.

Transmission revolution sensor (NC) input signal voltage is more than 1.9 V

3.

2 seconds

4.

1-trip detection logic


·

Transmission revolution sensor (NC)

·

Transmission wire

·

Harness and connector

·

ECM


Comes on DTC stored SAE Code
P07C6
P079114 Intermediate Shaft Speed Sensor "A" Circuit Short to Ground or Open 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The battery voltage is 8 V or more, the ignition switch is ON and the starter is off.

2.

Transmission revolution sensor (NC) input signal voltage is less than 0.1 V

3.

2 seconds

4.

1-trip detection logic


·

Transmission revolution sensor (NC)

·

Transmission wire

·

Harness and connector

·

ECM


Comes on DTC stored SAE Code
P07C5
P079131 Intermediate Shaft Speed Sensor "A" No Signal 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

All of the following conditions are met:

(a)

The battery voltage is 8 V or more.

(b)

Park/neutral position switch D input signal is ON

(c)

The vehicle speed is 25 km/h (16 mph) or more.

(d)

Speed indicated by transmission revolution sensor (NT) is higher than specified value


2.

Speed indicated by transmission revolution sensor (NC) is less than 300 rpm

3.

2 seconds

4.

1-trip detection logic


·

Transmission revolution sensor (NC)

·

Transmission wire

·

Harness and connector

·

ECM


Comes on DTC stored SAE Code
P0793

MONITOR DESCRIPTION

The transmission revolution sensor (NC) monitors the output shaft speed.

The ECM commands gear changes and controls the lock up timing based on the signals from the transmission revolution sensor (NC) and throttle position sensor.

If the vehicle is being driven at 25 km/h (16 mph) or more and the speed sensor (NC) signal sent to the ECM is less than 300 rpm, or if the transmission revolution sensor (NC) input signal voltage is less than 0.1 V or more than 1.9 V, the ECM will illuminate the MIL and store a DTC.

WIRING DIAGRAM

C367619E18
1,1.729 2.563,2.219 1.563,0.49 10 false Transmission Revolution Sensor (NC) 1.219,3.021 2.781,3.51 1.563,0.49 10 false Transmission Wire 5.469,3.167 5.927,3.365 0.458,0.198 10 false C1 5.458,3.313 5.917,3.51 0.458,0.198 10 false ECM 5.135,2.271 5.594,2.469 0.458,0.198 10 false NCO 4.844,2.271 5.302,2.469 0.458,0.198 10 false 72 4.833,1.146 5.292,1.344 0.458,0.198 10 false 73 5.135,1.146 5.594,1.344 0.458,0.198 10 false NCB 5.708,0.854 6.167,1.052 0.458,0.198 10 false 12 V 2.729,1.146 3.188,1.344 0.458,0.198 10 false NCB 2.729,2.271 3.188,2.469 0.458,0.198 10 false NCO 3.135,2.271 3.594,2.469 0.458,0.198 10 false 21 3.135,1.146 3.594,1.344 0.458,0.198 10 false 22 0.625,1.396 1.083,1.594 0.458,0.198 10 false 1 0.635,2.219 1.094,2.417 0.458,0.198 10 false 2 1.219,2.875 1.677,3.073 0.458,0.198 10 false C85

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.



DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Transmission / Data List / NC Sensor Speed.


g.

Read the Data List according to the display on the GTS.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
NC Sensor Speed Counter gear speed Min.: 0 rpm
Max.: 12750 rpm
- -
Powertrain > Transmission > Data List
Tester Display
NC Sensor Speed
50003 373 176
HINT:
·

NC Sensor Speed is always 0 while driving: Open or short in the sensor or circuit.

·

NC Sensor Speed is always more than 0 and less than 300 rpm while driving the vehicle at 16 km/h (10 mph) or more: Sensor malfunction, improper installation, or intermittent connection malfunction in the circuit.





PROCEDURE

1.READ VALUE USING GTS (NC SENSOR SPEED AND NC SENSOR VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Data List / NC Sensor Speed and NC Sensor Voltage.


e.

Read the Data List according to the display on the GTS.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
NC Sensor Speed Counter gear speed Min.: 0 rpm
Max.: 12750 rpm
- -
NC Sensor Voltage NC sensor voltage Min.: 0.000 V
Max.: 4.999 V
0.1 to 1.9 V: Engine idling -
Powertrain > Transmission > Data List
Tester Display
NC Sensor Speed
NC Sensor Voltage
50003 373 176,177

Result:
Result Proceed to
Data List values are normal A
Data List values are not normal B



A

5.REPLACE ECM

B

2.INSPECT TRANSMISSION REVOLUTION SENSOR (NC) (NC TERMINAL)
2.INSPECT TRANSMISSION REVOLUTION SENSOR (NC) (NC TERMINAL)
a.
C361134C17
1.469,0.146 1.906,0.417 0.438,0.271 1.292,1.25 0.833,1.75 true 1.375,1.26 1.75,1.75 true 1.563,0.198 2.021,0.396 0.458,0.198 10 false C85 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 0.688,1.813 1.146,2.01 0.458,0.198 10 false NCO 1.667,1.833 2.125,2.031 0.458,0.198 10 false NCB
*a Front view of wire harness connector
(to Transmission Wire)


Disconnect the C85 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C85-21 (NCO) - Body ground Always 99 to 101 Ω



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C85-22 (NCB) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSMISSION WIRE (TRANSMISSION REVOLUTION SENSOR (NC))

NG

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
3.INSPECT TRANSMISSION WIRE (TRANSMISSION REVOLUTION SENSOR (NC))
a.
C361135C04
1.698,1.385 1.333,1.917 true 1.885,1.385 2.333,1.917 true 2.031,3.708 1.75,4.167 true 2.125,3.708 2.5,4.167 true 0.75,0.667 1.063,0.865 0.313,0.198 10 false *a 0.75,2.75 1.063,2.948 0.313,0.198 10 false *b 1.271,1.99 1.427,2.188 0.156,0.198 10 false 1 2.292,1.979 2.448,2.177 0.156,0.198 10 false 2 1.583,4.177 2.042,4.375 0.458,0.198 10 false NCB 2.354,4.167 2.813,4.365 0.458,0.198 10 false NCO 0.083,0.083 0.542,0.281 0.458,0.198 10 false *1
*1 Transmission Wire
*a Transmission Revolution Sensor (NC) Side
*b Wire Harness Connector Side


Disconnect the transmission revolution sensor (NC) connector.

When Not Using the Engine Support Bridge: Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TRANSMISSION WIRE(When Not Using the Engine Support Bridge)>REMOVAL

When Using the Engine Support Bridge: Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TRANSMISSION WIRE(When Using the Engine Support Bridge)>REMOVAL


b.

Disconnect the C85 transmission wire connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (transmission revolution sensor (NC) side) - 22 (NCB) (wire harness connector side) Always Below 1 Ω
2 (transmission revolution sensor (NC) side) - 21 (NCO) (wire harness connector side) Always Below 1 Ω
1 (transmission revolution sensor (NC) side) or 22 (NCB) (wire harness connector side) - Body ground Always 10 kΩ or higher
2 (transmission revolution sensor (NC) side) or 21 (NCO) (wire harness connector side) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION REVOLUTION SENSOR (NC)

NG

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the C85 transmission wire connector.


b.

Disconnect the C1 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C85-22 (NCB) - C1-73 (NCB) Always Below 1 Ω
C85-21 (NCO) - C1-72 (NCO) Always Below 1 Ω
C85-22 (NCB) or C1-73 (NCB) - Body ground Always 10 kΩ or higher
C85-21 (NCO) or C1-72 (NCO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT