Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) › from 2018.09
RM3160E _58 Vehicle Interior _019712 SEAT _0107153 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) U

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  TERMINALS OF ECU  


CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY


a.

for LHD

B345461N04
3,0.083 3.333,0.292 0.333,0.208 4.25,0.083 4.583,0.292 0.333,0.208 3.094,0.094 3.542,0.406 0.448,0.313 10 false e6 4.344,0.094 4.771,0.375 0.427,0.281 10 false e7

i.

Disconnect the e6 and e7 position control ECU and switch assembly connectors.


ii.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
e6-2 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
e6-7 (+B) - e6-2 (GND) W - W-B Battery power supply Always 11 to 14 V
e7-12 (SYSB) - e6-2 (GND) G - W-B System power source Always 11 to 14 V
e7-3 (IG) - e6-2 (GND) Y - W-B Ignition power supply Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V


iii.

Reconnect the e6 and e7 position control ECU and switch assembly connectors.


iv.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
e6-6 (+B2) - e6-2 (GND) SB - W-B Lumbar support adjustment motor power source Always 11 to 14 V
e6-1 (GND2) - Body ground W-B - Body ground Lumbar support adjustment motor ground Always Below 1 Ω
e6-3 (SLD+) - e6-2 (GND) L - W-B Slide motor signal (forward) Slide switch off Below 1 V
Slide switch on (Forward) 11 to 14 V
e6-4 (SLD-) - e6-2 (GND) GR - W-B Slide motor signal (rearward) Slide switch off Below 1 V
Slide switch on (Rearward) 11 to 14 V
e6-5 (FRV-) - e6-2 (GND) R - W-B Front vertical motor signal (downward) Front vertical switch off Below 1 V
Front vertical switch on (Downward) 11 to 14 V
e6-8 (FRV+) - e6-2 (GND) B - W-B Front vertical motor signal (upward) Front vertical switch off Below 1 V
Front vertical switch on (Upward) 11 to 14 V
e6-9 (RCL+) - e6-2 (GND) P - W-B Reclining motor signal (forward) Reclining switch off Below 1 V
Reclining switch on (Forward) 11 to 14 V
e6-11 (RCL-) - e6-2 (GND) LG - W-B Reclining motor signal (rearward) Reclining switch off Below 1 V
Reclining switch on (Rearward) 11 to 14 V
e6-10 (LFT+) - e6-2 (GND) V - W-B Lifter motor signal (upward) Lifter switch off Below 1 V
Lifter switch on (Upward) 11 to 14 V
e6-12 (LFT-) - e6-2 (GND) G - W-B Lifter motor signal (downward) Lifter switch off Below 1 V
Lifter switch on (Downward) 11 to 14 V



b.

for RHD

B345462N05
2.583,0.083 2.917,0.292 0.333,0.208 3.833,0.083 4.167,0.292 0.333,0.208 2.688,0.104 3.01,0.271 0.323,0.167 10 false d7 3.948,0.104 4.24,0.271 0.292,0.167 10 false d6

i.

Disconnect the d6 and d7 position control ECU and switch assembly connectors.


ii.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
d6-2 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
d6-7 (+B) - d6-2 (GND) W - W-B Battery power supply Always 11 to 14 V
d7-12 (SYSB) - d6-2 (GND) BE - W-B System power source Always 11 to 14 V
d7-3 (IG) - d6-2 (GND) Y - W-B Ignition power supply Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V


iii.

Reconnect the d6 and d7 position control ECU and switch assembly connectors.


iv.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
d6-6 (+B2) - d6-2 (GND) SB - W-B Lumbar support adjustment motor power source Always 11 to 14 V
d6-1 (GND2) - Body ground W-B - Body ground Lumbar support adjustment motor ground Always Below 1 Ω
d6-3 (SLD+) - d6-2 (GND) L - W-B Slide motor signal (forward) Slide switch off Below 1 V
Slide switch on (Forward) 11 to 14 V
d6-4 (SLD-) - d6-2 (GND) GR - W-B Slide motor signal (rearward) Slide switch off Below 1 V
Slide switch on (Rearward) 11 to 14 V
d6-5 (FRV-) - d6-2 (GND) R - W-B Front vertical motor signal (downward) Front vertical switch off Below 1 V
Front vertical switch on (Downward) 11 to 14 V
d6-8 (FRV+) - d6-2 (GND) B - W-B Front vertical motor signal (upward) Front vertical switch off Below 1 V
Front vertical switch on (Upward) 11 to 14 V
d6-9 (RCL+) - d6-2 (GND) P - W-B Reclining motor signal (forward) Reclining switch off Below 1 V
Reclining switch on (Forward) 11 to 14 V
d6-11 (RCL-) - d6-2 (GND) LG - W-B Reclining motor signal (rearward) Reclining switch off Below 1 V
Reclining switch on (Rearward) 11 to 14 V
d6-10 (LFT+) - d6-2 (GND) V - W-B Lifter motor signal (upward) Lifter switch off Below 1 V
Lifter switch on (Upward) 11 to 14 V
d6-12 (LFT-) - d6-2 (GND) G - W-B Lifter motor signal (downward) Lifter switch off Below 1 V
Lifter switch on (Downward) 11 to 14 V




CHECK OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)


B343031C09
4.792,0.156 5.188,0.375 0.396,0.219 1.99,0.135 2.385,0.354 0.396,0.219 2.74,0.135 3.135,0.354 0.396,0.219 4.052,0.156 4.448,0.375 0.396,0.219 4.198,0.188 4.708,0.406 0.51,0.219 10 false I2 2.083,0.167 2.594,0.385 0.51,0.219 10 false z10 2.427,0.156 2.938,0.375 0.51,0.219 12 false *A 2.875,0.156 3.385,0.375 0.51,0.219 10 false z9 3.167,0.146 3.677,0.365 0.51,0.219 12 false *B 4.49,0.177 5,0.396 0.51,0.219 12 false *A 4.917,0.188 5.427,0.406 0.51,0.219 10 false H2 5.229,0.177 5.74,0.396 0.51,0.219 12 false *B
*A for LHD *B for RHD


a.

for LHD

i.

Disconnect the I2 outer mirror control ECU assembly (driver door) connector.


ii.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I2-6 (CPUB) - I2-7 (GND) BE - BR Battery power supply Always 11 to 14 V
I2-14 (BDR) - I2-7 (GND) L - BR Battery power supply Always 11 to 14 V
I2-5 (SIG) - I2-7 (GND) R - BR Ignition power supply Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
I2-7 (GND) - Body ground BR - Body ground Ground Always Below 1 Ω


iii.

Reconnect the I2 outer mirror control ECU assembly (driver door) connector.


iv.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I2-1 (MM) - I2-7 (GND) LG - BR SET switch signal for seat memory switch (driver door) SET switch on Below 1 V
SET switch off 11 to 14 V
I2-2 (M1) - I2-7 (GND) Y - BR M1 switch signal for seat memory switch (driver door) M1 switch on Below 1 V
M1 switch off 11 to 14 V
I2-3 (M2) - I2-7 (GND) G - BR M2 switch signal for seat memory switch (driver door) M2 switch on Below 1 V
M2 switch off 11 to 14 V



b.

for RHD

i.

Disconnect the H2 outer mirror control ECU assembly (driver door) connector.


ii.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H2-6 (CPUB) - H2-7 (GND) BE - BR Battery power supply Always 11 to 14 V
H2-14 (BDR) - H2-7 (GND) L - BR Battery power supply Always 11 to 14 V
H2-5 (SIG) - H2-7 (GND) V - BR Ignition power supply Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
H2-7 (GND) - Body ground BR - Body ground Ground Always Below 1 Ω


iii.

Reconnect the H2 outer mirror control ECU assembly (driver door) connector.


iv.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H2-1 (MM) - H2-7 (GND) P - BR SET switch signal for seat memory switch (driver door) SET switch on Below 1 V
SET switch off 11 to 14 V
H2-2 (M1) - H2-7 (GND) B - BR M1 switch signal for seat memory switch (driver door) M1 switch on Below 1 V
M1 switch off 11 to 14 V
H2-3 (M2) - H2-7 (GND) G - BR M2 switch signal for seat memory switch (driver door) M2 switch on Below 1 V
M2 switch off 11 to 14 V




CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


B357833C01
4.99,3.521 5.396,3.792 0.406,0.271 1.427,4.823 1.833,5.094 0.406,0.271 4.083,4.802 4.49,5.073 0.406,0.271 5.573,4.927 5.979,5.198 0.406,0.271 1.354,6.396 1.76,6.667 0.406,0.271 4.865,6.396 5.271,6.667 0.406,0.271 6.469,4.927 6.875,5.198 0.406,0.271 3.458,7.969 3.865,8.24 0.406,0.271 1.792,3.521 2.198,3.792 0.406,0.271 2.25,0.25 2.083,0.25 2.083,0.25 2.083,0.604 false 2.5,2.083 2.25,2.083 2.25,2.083 2.167,2.083 false 2.5,1.583 2.25,1.583 2.25,1.583 2.167,1.583 false 2.021,1.583 1.667,1.583 1.667,1.583 1.667,2.417 false 2.021,2.083 1.75,2.083 1.75,2.083 1.667,2.083 false 4.833,0.198 4.667,0.198 4.667,0.198 4.667,0.552 false 0.125,0.094 0.5,0.333 0.375,0.24 12 false *A 0.552,1.052 0.75,1.25 0.198,0.198 10 false 4H 0.552,1.802 0.75,2 0.198,0.198 10 false 4F 0.563,2.24 0.76,2.438 0.198,0.198 10 false 4K 0.833,2.51 1.031,2.708 0.198,0.198 10 false 4L 2.365,0.156 2.563,0.354 0.198,0.198 10 false *1 2.563,1.479 2.99,1.719 0.427,0.24 10 false F19 2.583,1.969 2.958,2.25 0.375,0.281 10 false F18 1.604,2.448 1.802,2.646 0.198,0.198 10 false *a 4.917,0.083 5.167,0.25 0.25,0.167 10 false MB 6.458,0.906 6.656,1.104 0.198,0.198 10 false 4D 6.458,1.74 6.656,1.938 0.198,0.198 10 false 4A 1.875,3.573 2.396,3.802 0.521,0.229 10 false F18 5.083,3.573 5.771,3.938 0.688,0.365 10 false F19 1.552,4.885 1.833,5.083 0.281,0.198 10 false 4H 4.208,4.854 4.406,5.052 0.198,0.198 10 false 4F 5.698,4.99 6.021,5.208 0.323,0.219 10 false 4K 1.479,6.448 1.677,6.646 0.198,0.198 10 false 4D 4.99,6.448 5.188,6.646 0.198,0.198 10 false 4A 6.604,4.99 6.802,5.188 0.198,0.198 10 false 4L 3.563,8.021 3.844,8.271 0.281,0.25 10 false MB
*A Main Body ECU (Multiplex Network Body ECU) with 2 Connectors - -
*1 Main Body ECU (Multiplex Network Body ECU) - -
*a 2 Connectors - -


B357834C01
1.083,3.479 1.5,3.75 0.417,0.271 3.594,3.5 4.01,3.771 0.417,0.271 5.917,3.479 6.333,3.75 0.417,0.271 1.417,4.833 1.833,5.104 0.417,0.271 4.042,4.833 4.458,5.104 0.417,0.271 5.563,4.906 5.979,5.177 0.417,0.271 1.385,6.396 1.802,6.667 0.417,0.271 4.844,6.396 5.26,6.667 0.417,0.271 6.438,4.906 6.854,5.177 0.417,0.271 3.417,7.958 3.833,8.229 0.417,0.271 2.083,0.604 2.083,0.25 2.083,0.25 2.25,0.25 false 2.167,1.083 2.583,1.083 false 2.167,1.583 2.583,1.583 false 2.167,2.083 2.583,2.083 false 1.667,1.583 2.021,1.583 false 1.667,2.083 2.021,2.083 false 1.667,2.5 1.667,1.083 1.667,1.083 2.021,1.083 false 4.583,0.552 4.583,0.198 4.583,0.198 4.75,0.198 false 0.156,0.135 0.531,0.375 0.375,0.24 12 false *A 0.552,1.052 0.833,1.219 0.281,0.167 10 false 4H 0.552,1.823 0.833,1.99 0.281,0.167 10 false 4F 0.563,2.25 0.844,2.417 0.281,0.167 10 false 4K 0.833,2.521 1.115,2.688 0.281,0.167 10 false 4L 2.302,0.188 2.615,0.385 0.313,0.198 10 false *1 1.594,2.531 1.906,2.729 0.313,0.198 10 false *a 2.646,1.01 3.104,1.26 0.458,0.25 10 false F20 2.656,1.51 3.104,1.771 0.448,0.26 10 false F19 2.656,2.01 3.094,2.24 0.438,0.229 10 false F18 4.813,0.125 5.156,0.344 0.344,0.219 10 false MB 6.458,0.927 6.823,1.094 0.365,0.167 10 false 4D 6.458,1.75 6.823,1.917 0.365,0.167 10 false 4A 1.177,3.531 1.458,3.698 0.281,0.167 10 false F18 3.688,3.563 4.219,3.823 0.531,0.26 10 false F19 6.021,3.542 6.479,3.781 0.458,0.24 10 false F20 1.531,4.896 1.813,5.063 0.281,0.167 10 false 4H 4.177,4.896 4.458,5.063 0.281,0.167 10 false 4F 5.688,4.979 5.969,5.146 0.281,0.167 10 false 4K 3.521,8.021 3.885,8.25 0.365,0.229 10 false MB 1.521,6.458 1.802,6.625 0.281,0.167 10 false 4D 4.969,6.458 5.25,6.625 0.281,0.167 10 false 4A 6.573,4.969 6.854,5.135 0.281,0.167 10 false 4L
*A Main Body ECU (Multiplex Network Body ECU) with 3 Connectors - -
*1 Main Body ECU (Multiplex Network Body ECU) - -
*a 3 Connectors - -


a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Reconnect the instrument panel junction block assembly connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
MB-31 (BECU) - Body ground - Battery power supply Always 11 to 14 V
MB-32 (IG) - Body ground - Ignition power supply Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
MB-30 (ACC) - Body ground - Ignition power supply Engine switch on (ACC) 11 to 14 V
Engine switch off Below 1 V
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
F19-6 (FLCY) - Body ground*1 SB - Body ground Front door courtesy light switch assembly (driver door) input Front door LH closed (OFF) → open (ON) 10 kΩ or higher → Below 1 Ω
F19-27 (FRCY) - Body ground*2 L - Body ground Front door courtesy light switch assembly (driver door) input Front door RH closed (OFF) → open (ON) 10 kΩ or higher → Below 1 Ω

*1: for LHD

*2: for RHD