Home › Drivetrain › UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › from 2018.09
RM3160E _52 Drivetrain _060165 UA80F AUTOMATIC TRANSMISSION / TRANSAXLE _0303922 AUTOMATIC TRANSAXLE SYSTEM C

UA80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P27567F  Torque Converter Clutch Pressure Control Solenoid Control Actuator Stuck Off  


DESCRIPTION

The ECM controls the solenoid (SLU) valve using a predetermined current, and performs lock-up and flex lock-up control.

The ECM compares the engagement condition of the lock-up clutch with the lock-up schedule in the ECM memory to detect mechanical malfunctions of the solenoid (SLU) valve, transmission valve body assembly and torque converter assembly.

C361130C02
4.833,1.667 4.083,0.75 4.083,0.75 3.917,0.75 true 5,1.917 4.5,2.5 4.5,2.5 4.333,2.5 true 6.083,1.417 5.417,2.833 5.417,2.833 6.083,2 true 1.917,2.813 2.99,3.01 1.073,0.198 10 false *a 0.708,2.104 1.302,2.521 0.594,0.417 10 false *b 5.323,2.865 5.917,3.156 0.594,0.292 10 false *3 4.146,2.427 5.063,2.625 0.917,0.198 10 false *2 3.729,0.667 5.417,0.865 1.688,0.198 10 false *1
*1 Spool Valve *2 Sleeve
*3 Solenoid Coil - -
*a Current *b Hydraulic Pressure


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P27567F Torque Converter Clutch Pressure Control Solenoid Control Actuator Stuck Off 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
SLU stuck ON malfunction:
1.

Engine coolant temperature is 40°C (104°F) or higher, ATF temperature is -10°C (14°F) or higher, and the ECM sends a lock-up off request (no malfunctions are detected in the solenoid (SL1, SL2, SL3, SL4, SL5, SL6, SL, SLT and SLU) valves, transmission revolution sensors (NT, NC), engine coolant temperature sensor, ATF temperature sensor, knock control sensor, electronic throttle, crankshaft position sensor or CAN2)

2.

The difference between the input turbine speed (NT) and the engine speed (NE) is less than 35 rpm

3.

1.8 seconds or more

4.

2-trip detection logic


SLU stuck OFF malfunction:
1.

Engine coolant temperature is 40°C (104°F) or higher, ATF temperature is -10°C (14°F) or higher, and the ECM sends a lock-up on request (no malfunctions are detected in the solenoid (SL1, SL2, SL3, SL4, SL5, SL6, SL, SLT and SLU) valves, transmission revolution sensors (NT, NC), engine coolant temperature sensor, ATF temperature sensor, knock control sensor, electronic throttle, crankshaft position sensor or CAN2)

2.

The difference between the input turbine speed (NT) and the engine speed (NE) is 120 rpm or more

3.

3.5 seconds or more

4.

2-trip detection logic


·

Solenoid (SLU) valve

·

Transmission valve body assembly

·

Torque converter assembly

·

Automatic transaxle assembly


Comes on DTC stored SAE Code:
P2757

MONITOR DESCRIPTION

Torque converter lock-up is controlled by the ECM based on the transmission revolution sensor (NT and NC), engine speed, engine load, engine temperature, vehicle speed, ATF temperature and gear selection signals. The ECM determines the lock-up status of the torque converter assembly by comparing the engine speed (NE) to the transmission revolution sensor (NT) signal. The ECM calculates the actual gear by comparing the transmission revolution sensor (NT) signal to the transmission revolution sensor (NC) signal. When conditions are appropriate, the ECM requests "lock-up" by applying voltage to the solenoid (SLU) valve. When the solenoid (SLU) valve is turned on, pressure is applied to the lock-up relay valve and locks the torque converter assembly.

If the ECM does not detect lock-up after lock-up has been requested or if it detects lock-up when it is not requested, it interprets this as a malfunction of the solenoid (SLU) valve, illuminates the MIL and stores this DTC.

HINT:

Example:

When any of the following is met, the system judges it as a malfunction.

·

There is a difference in speed between the input side (engine speed) and output side (input turbine speed) of the torque converter assembly when the ECM commands lock-up. (Engine speed is at least 120 rpm more than input turbine speed.)

·

There is no difference in speed between the input side (engine speed) and output side (input turbine speed) of the torque converter assembly when the ECM commands lock-up off. (The difference between engine speed and input turbine speed is less than 35 rpm.)



CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Perform the Lock-up Function inspection in Road Test.

Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>ROAD TEST

2.

Turn the ignition switch off.

3.

Perform step (1) again.



PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P27567F)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Trouble Codes.

Powertrain > Transmission > Trouble Codes
50001 373

e.

Read the DTCs using the GTS.

Result:
Result Proceed to
Only DTC P27567F is output A
DTC P27567F and other DTCs are output B


HINT:
·

If any DTCs other than P27567F are output, perform troubleshooting for those DTCs first.

·

If a solenoid valve is stuck ON or OFF, DTCs for several solenoid valves including the malfunctioning solenoid valve will be stored.





A

2.INSPECT SOLENOID (SLU) VALVE

B

2.INSPECT SOLENOID (SLU) VALVE
a.
C197715C76
1.75,1 2.198,0.417 true 1.5,1.01 1.042,0.427 true 1.75,2.979 2.198,2.385 true 1.479,2.979 1.021,2.385 true 0.073,0.083 0.469,0.344 0.396,0.26 10 false *a 2.25,0.24 2.521,0.5 0.271,0.26 10 false 1 0.896,0.25 1.156,0.5 0.26,0.25 10 false 2 2.281,2.198 2.521,2.479 0.24,0.281 10 false 1 0.875,2.219 1.156,2.49 0.281,0.271 10 false 2 1.865,3.948 2.271,4.271 0.406,0.323 10 false (+) 1.219,3.948 1.594,4.25 0.375,0.302 10 false (-)
*a Component without harness connected
(Solenoid (SLU) Valve)


Remove the solenoid (SLU) valve.

Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Solenoid (SLU) valve connector terminal 1 - Terminal 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Inspect the transmission valve body assembly.

Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>REMOVAL

OK:

There is no foreign matter on each valve and they operate smoothly.



Result:
Proceed to
OK
NG



OK

4.INSPECT TORQUE CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

4.INSPECT TORQUE CONVERTER ASSEMBLY
a.

Inspect the torque converter assembly.

Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER AND DRIVE PLATE>INSPECTION

OK:

The torque converter assembly is normal.



Result:
Proceed to
OK
NG



OK

5.REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSEMBLY

NG

5.REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSEMBLY

Result:
Proceed to
NEXT



NEXT