The main body ECU (multiplex network body ECU) controls the high beam headlights.
w/ Projector Headlight
w/o Projector Headlight
Inspect the fuses for circuits related to this system before performing the following procedure.
The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
*: w/ Door Control Battery
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Head Light Hi | High beam headlights | OFF or ON | - |
| Tester Display |
|---|
| Head Light Hi |
High beam headlights illuminate.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Projector Headlight) | B |
| NG (w/o Projector Headlight) | C |
A
B
C
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (DIMMER relay) - Body ground | Ignition switch off*1
Always*2 |
11 to 14 V |
| 5 (DIMMER relay) - Body ground | Ignition switch off*1
Always*2 |
11 to 14 V |
*1: for HV Model
*2: for Gasoline Model
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A66 headlight assembly LH connector.
Disconnect the A65 headlight assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (DIMMER relay) - A66-6 (HI) | Always | Below 1 Ω |
| 3 (DIMMER relay) - A65-6 (HI) | Always | Below 1 Ω |
| 3 (DIMMER relay) or A66-6 (HI) - Body ground | Always | 10 kΩ or higher |
| 3 (DIMMER relay) or A65-6 (HI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H43 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (DIMMER relay) - H43-13 (DIM) | Always | Below 1 Ω |
| 1 (DIMMER relay) or H43-13 (DIM) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A66 headlight assembly LH connector.
Disconnect the A65 headlight assembly RH connector.
Disconnect the H43 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A66-6 (HI) - H43-13 (DIM) | Always | Below 1 Ω |
| A65-6 (HI) - H43-13 (DIM) | Always | Below 1 Ω |
| A66-6 (HI) or H43-13 (DIM) - Body ground | Always | 10 kΩ or higher |
| A65-6 (HI) or H43-13 (DIM) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG