Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM37A0E _59 Vehicle Exterior _086888 LIGHTING (EXT) _0415934 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  LO-beam Headlight does not Illuminate  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the low beam headlights.

WIRING DIAGRAM

E432636E01
0.74,0.385 2.438,0.667 1.698,0.281 10 false from Auxiliary Battery 0.74,1.76 2.385,2.125 1.646,0.365 10 false from Auxiliary Battery 0.656,1.031 1.292,1.354 0.635,0.323 10 false H-LP LH 1.948,1.417 2.583,1.698 0.635,0.281 10 false H-LP LH 0.646,2.406 1.271,2.688 0.625,0.281 10 false H-LP RH 1.927,2.802 2.625,3.031 0.698,0.229 10 false H-LP RH 1.823,0.76 1.99,0.969 0.167,0.208 10 false 5 1.823,1.031 1.99,1.24 0.167,0.208 10 false 2 2.469,0.76 2.635,0.969 0.167,0.208 10 false 3 2.469,1.031 2.635,1.24 0.167,0.208 10 false 1 1.833,2.135 2,2.344 0.167,0.208 10 false 5 1.844,2.417 2.01,2.625 0.167,0.208 10 false 2 2.479,2.135 2.646,2.344 0.167,0.208 10 false 3 2.479,2.406 2.646,2.615 0.167,0.208 10 false 1 4.198,1.5 4.49,1.719 0.292,0.219 10 false 4C 4.323,1.021 4.615,1.24 0.292,0.219 10 false 31 4.208,1.656 5.802,2.188 1.594,0.531 10 false Instrument Panel Junction Block Assembly 5.833,1.135 6.125,1.354 0.292,0.219 10 false MB 5.833,0.927 6.125,1.146 0.292,0.219 10 false 15 6.188,1.021 6.781,1.292 0.594,0.271 10 false HRLY 6.188,2.396 6.781,2.667 0.594,0.271 10 false HRY2 5.802,2.51 6.094,2.729 0.292,0.219 10 false H43 5.844,2.302 6.135,2.521 0.292,0.219 10 false 12 5.51,4.208 7.156,4.667 1.646,0.458 10 false Main Body ECU (Multiplex Network Body ECU) 2.448,3.448 2.771,3.677 0.323,0.229 10 false LO 2.448,4.667 2.771,4.896 0.323,0.229 10 false LO 1.76,4.667 2.083,4.896 0.323,0.229 10 false E 1.76,3.438 2.083,3.667 0.323,0.229 10 false E 1.438,3.896 2.854,4.135 1.417,0.24 10 false A66 1.458,5.146 3.083,5.469 1.625,0.323 10 false A65 1.438,4.042 3.063,4.281 1.625,0.24 10 false Headlight Assembly LH 1.458,5.292 3.083,5.531 1.625,0.24 10 false Headlight Assembly RH 2.708,3.333 3.083,3.594 0.375,0.26 10 false 1 1.583,3.333 1.927,3.542 0.344,0.208 10 false 4 1.573,4.552 1.917,4.76 0.344,0.208 10 false 4 2.698,4.563 3.073,4.823 0.375,0.26 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

*: w/ Door Control Battery




PROCEDURE

1.CHECK LIGHTS
a.

Check the illumination of each low beam lights.


Result:
Result Proceed to
LH side low beam light does not illuminate A
RH side low beam light does not illuminate B



A

2.PERFORM ACTIVE TEST USING GTS

B

10.PERFORM ACTIVE TEST USING GTS
2.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Headlight Relay Low beam headlights OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Headlight Relay
50004 123 14
OK:

Low beam headlights illuminate.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.INSPECT HEADLIGHT ASSEMBLY LH (LO TERMINAL VOLTAGE)
3.INSPECT HEADLIGHT ASSEMBLY LH (LO TERMINAL VOLTAGE)
E367359C59
1.521,0.677 1.885,0.958 0.365,0.281 0.844,2.583 1.302,1.802 false 1.573,0.719 2.031,0.917 0.458,0.198 10 false A66 0.25,0.344 0.708,0.542 0.458,0.198 10 false *a 0.677,2.615 1.146,2.823 0.469,0.208 10 false LO
*a Front view of wire harness connector
(to Headlight Assembly LH)


a.

Disconnect the A66 headlight assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A66-1 (LO) - Body ground Light control switch in head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - BODY GROUND)

NG

5.CHECK HARNESS AND CONNECTOR (H-LP LH RELAY - HEADLIGHT ASSEMBLY LH)
4.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (H-LP LH RELAY - HEADLIGHT ASSEMBLY LH)
a.

Remove the H-LP LH relay.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (H-LP LH relay) - A66-1 (LO) Always Below 1 Ω
3 (H-LP LH relay) or A66-1 (LO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT H-LP LH RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT H-LP LH RELAY

OK

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE - H-LP LH RELAY)

NG

REPLACE H-LP LH RELAY

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE - H-LP LH RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (H-LP LH relay) - Body ground Ignition switch off*1
Always*2
11 to 14 V
5 (H-LP LH relay) - Body ground Ignition switch off*1
Always*2
11 to 14 V


*1: for HV Model

*2: for Gasoline Model



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (H-LP LH RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (H-LP LH RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4C instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (H-LP LH relay) - 4C-31 Always Below 1 Ω
1 (H-LP LH relay) or 4C-31 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E367360C35
1.74,0.583 2.115,0.833 0.375,0.25 4.875,0.938 5.25,1.188 0.375,0.25 4.563,2.052 4.938,1.542 false 0.479,0.438 0.792,0.635 0.313,0.198 10 false *a 1.833,0.625 2.146,0.823 0.313,0.198 10 false 4C 4.948,0.979 5.26,1.177 0.313,0.198 10 false MB 4.396,2.083 4.927,2.313 0.531,0.229 10 false HRLY
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4C-31 - MB-15 (HRLY) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

10.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Headlight Relay Low beam headlights OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Headlight Relay
50004 123 14
OK:

Low beam headlights illuminate.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

11.INSPECT HEADLIGHT ASSEMBLY RH (LO TERMINAL VOLTAGE)
11.INSPECT HEADLIGHT ASSEMBLY RH (LO TERMINAL VOLTAGE)
E367359C60
1.5,0.677 1.865,0.958 0.365,0.281 0.792,2.635 1.313,1.813 false 1.552,0.719 2.01,0.917 0.458,0.198 10 false A65 0.25,0.344 0.708,0.542 0.458,0.198 10 false *a 0.604,2.656 1.063,2.854 0.458,0.198 10 false LO
*a Front view of wire harness connector
(to Headlight Assembly RH)


a.

Disconnect the A65 headlight assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A65-1 (LO) - Body ground Light control switch in head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - BODY GROUND)

NG

13.CHECK HARNESS AND CONNECTOR (H-LP RH RELAY - HEADLIGHT ASSEMBLY RH)
12.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A65-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (H-LP RH RELAY - HEADLIGHT ASSEMBLY RH)
a.

Remove the H-LP RH relay.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (H-LP RH relay) - A65-1 (LO) Always Below 1 Ω
3 (H-LP RH relay) or A65-1 (LO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.INSPECT H-LP RH RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT H-LP RH RELAY

OK

15.CHECK HARNESS AND CONNECTOR (POWER SOURCE - H-LP RH RELAY)

NG

REPLACE H-LP RH RELAY

15.CHECK HARNESS AND CONNECTOR (POWER SOURCE - H-LP RH RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (H-LP RH relay) - Body ground Ignition switch off*1
Always*2
11 to 14 V
5 (H-LP RH relay) - Body ground Ignition switch off*1
Always*2
11 to 14 V


*1: for HV Model

*2: for Gasoline Model



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (H-LP RH RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (H-LP RH RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the H43 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (H-LP RH relay) - H43-12 (HRY2) Always Below 1 Ω
1 (H-LP RH relay) or H43-12 (HRY2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR