The automatic light control sensor detects ambient light. The sensor creates an electrical signal based on the amount of light detected, and sends the signal to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) turns on or off the headlights and taillights according to the signal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| B1244 | Light Sensor Circuit | Detection condition:
The ignition switch is ON. Malfunction status:
Either of the following conditions is met: -
Malfunction in automatic light control sensor -
Open or short in automatic light control sensor circuit Malfunction duration:
5 seconds or more |
·
Automatic light control sensor ·
Harness or connector ·
Main body ECU (multiplex network body ECU) |
Main Body |
The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
*: w/ Door Control Battery
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch to ON.
Wait 10 seconds or more.
Check for DTCs.
DTC B1244 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
According to the display on the GTS, read the Data List and check that the value of Light Sensor Illuminance changes while performing the following:
Cover the automatic light control sensor with an opaque object.
Slowly move the opaque object to uncover and then cover the automatic light control sensor.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Light Sensor Illuminance | Light control sensor illuminance | 0 to 8191 lx or SensorFail | Value is output according to ambient light level | The displayed value is "0" when no light is detected. |
| Tester Display |
|---|
| Light Sensor Illuminance |
The value changes according to the amount the automatic light control sensor is covered.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G5 automatic light control sensor connector.
Disconnect the H43 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G5-1 (CLTB) - H43-23 (CLTB) | Always | Below 1 Ω |
| G5-4 (CLTS) - H43-24 (CLTS) | Always | Below 1 Ω |
| G5-2 (CLTE) - H43-25 (CLTE) | Always | Below 1 Ω |
| G5-1 (CLTB) or H43-23 (CLTB) - Body ground | Always | 10 kΩ or higher |
| G5-4 (CLTS) or H43-24 (CLTS) - Body ground | Always | 10 kΩ or higher |
| G5-2 (CLTE) or H43-25 (CLTE) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Main Body ECU (Multiplex Network Body ECU)) |
Connect the H43 main body ECU (multiplex network body ECU) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H43-23 (CLTB) - H43-25 (CLTE) | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC LIGHT CONTROL SENSOR>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG