The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front seat assembly RH removal/installation are shown below.
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
Wear protective gloves. Sharp areas on the parts may injure your hands.
If the front seat airbag assembly has been deployed, replace the front seat airbag assembly, separate type front seatback spring assembly, separate type front seatback pad and separate type front seatback cover with the necessary parts in accordance with the extent of the collision damage.
After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
58441L
2.REMOVE BATTERY SERVICE HOLE COVER (for HV Model)
3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for HV Model: Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>REMOVAL
for Gasoline Model: Click hereGeneral>MAINTENANCE>2GR-FKS BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
71910A
4.REMOVE FRONT SEAT HEADREST ASSEMBLY
Remove the front seat headrest assembly from the front seat assembly RH.
72123A
5.REMOVE FRONT OUTER SEAT TRACK BRACKET COVER
Operate the seat track adjusting handle and move the front seat assembly RH to the rearmost position.
Disengage the 2 claws to remove the front outer seat track bracket cover.
72127A
6.REMOVE FRONT INNER SEAT TRACK BRACKET COVER
Disengage the 2 claws to remove the front inner seat track bracket cover.
72137B
7.REMOVE SEAT TRACK COVER
Operate the seat track adjusting handle and move the front seat assembly RH to the foremost position.
Disengage the 2 claws and guide to remove the seat track cover.
72157A
8.REMOVE INNER SEAT TRACK BRACKET COVER
Disengage the 2 claws and guide to remove the inner seat track bracket cover.
9.REMOVE FRONT SEAT ASSEMBLY RH
Using a T50 "TORX" socket wrench, remove the 2 bolts on the rear side of the front seat assembly RH.
Operate the seat track adjusting handle and move the front seat assembly RH to the rearmost position.
Using a T50 "TORX" socket wrench, remove the 2 bolts on the front side of the front seat assembly RH.
Operate the seat track adjusting handle and move the front seat assembly RH to the center position.
Operate the reclining adjuster release handle and move the seatback to the upright position.
Disconnect the front seat airbag assembly connector under the front seat assembly RH.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
| *a | White Housing Lock |
| *b | Yellow CPA |
|
Slide in this Direction |
Push down the white housing lock and slide the yellow CPA as shown in the illustration. (At this time, the connector cannot be disconnected yet.)
Push down the white housing lock again and disconnect the connector.
Do not push down the part (A) shown in the illustration when disconnecting the connector.
Disconnect each connector and disengage each clamp under the front seat assembly RH.
Remove the front seat assembly RH.
Be careful not to damage the vehicle body.