Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Power Seat) › 2020.02–2020.11
RM37A0E _58 Vehicle Interior _086894 SEAT _0416490 FRONT SEAT ASSEMBLY(for Power Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Power Seat)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front seat assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
·

Position control ECU assembly (driver seat)*

·

Reclining motor (separate type front seatback spring assembly (driver seat))*

·

Slide motor (separate type front seat cushion spring assembly (driver seat))*

·

Front vertical motor (power seat tilt motor assembly (driver seat))*

·

Lifter motor (power seat lifter motor assembly (driver seat))*


Initialize position control ECU Front Power Seat Control System (w/ Memory) (Click here)

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
·

Position control ECU assembly (driver seat)*

·

Reclining motor (separate type front seatback spring assembly (driver seat))*

·

Slide motor (separate type front seat cushion spring assembly (driver seat))*

·

Front vertical motor (power seat tilt motor assembly (driver seat))*

·

Lifter motor (power seat lifter motor assembly (driver seat))*


Initialize position control ECU Front Power Seat Control System (w/ Memory) (Click here)

CAUTION:
·
B401522

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·
B543257

Wear protective gloves. Sharp areas on the parts may injure your hands.



NOTICE:
·

If the front seat airbag assembly has been deployed, replace the front seat airbag assembly, separate type front seatback spring assembly, separate type front seatback pad and separate type front seatback cover with the necessary parts in accordance with the extent of the collision damage.

·

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 58441L 2.REMOVE BATTERY SERVICE HOLE COVER (for HV Model)

Hide 71910A 3.REMOVE FRONT SEAT HEADREST ASSEMBLY

a.

Remove the front seat headrest assembly from the front seat assembly.


Hide 72124 4.REMOVE FRONT OUTER SEAT TRACK BRACKET COVER

a.

Operate the slide and vertical power seat switch knob and move the front seat assembly to the rearmost position.


b.
B564717

Disengage the 2 claws to remove the front outer seat track bracket cover.


Hide 72128A 5.REMOVE FRONT INNER SEAT TRACK BRACKET COVER

a.
B564718

Disengage the 2 claws to remove the front inner seat track bracket cover.


Hide 72138B 6.REMOVE SEAT TRACK COVER

a.

Operate the slide and vertical power seat switch knob and move the front seat assembly to the foremost position.


b.
B564719

Disengage the 2 claws and guide to remove the seat track cover.


Hide 72158 7.REMOVE INNER SEAT TRACK BRACKET COVER

a.
B564720

Disengage the 2 claws and guide to remove the inner seat track bracket cover.


Hide 8.REMOVE FRONT SEAT ASSEMBLY

a.
B564721

Using a T50 "TORX" socket wrench, remove the 2 bolts on the rear side of the front seat assembly.


b.

Operate the slide and vertical power seat switch knob and move the front seat assembly to the rearmost position.


c.
B564722

Using a T50 "TORX" socket wrench, remove the 2 bolts on the front side of the front seat assembly.


d.

Operate the reclining power seat switch knob and move the seatback to the upright position.


e.

Operate the slide and vertical power seat switch knob and move the front seat assembly to the center position.


f.

for Driver Side:

i.

Operate the slide and vertical power seat switch knob and move the front seat assembly to the uppermost position.



g.

Disconnect the cable from the negative (-) auxiliary battery terminal.

for HV Model: Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>REMOVAL

for Gasoline Model: Click hereGeneral>MAINTENANCE>2GR-FKS BATTERY>REMOVAL

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



h.

Disconnect the front seat airbag assembly connector under the front seat assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


i.
B474821C04
1.75,1.083 2.333,1.083 true 1.948,1.385 2.531,1.385 false 1.052,1.417 1.635,1.417 true 2.375,0.99 2.688,1.146 0.313,0.156 10 false *a 2.563,1.313 2.875,1.469 0.313,0.156 10 false *b 0.927,1.333 1.104,1.521 0.177,0.188 10 false A
*a White Housing Lock
*b Yellow CPA
V113147

Slide in this Direction


Push down the white housing lock and slide the yellow CPA as shown in the illustration. (At this time, the connector cannot be disconnected yet.)


ii.

Push down the white housing lock again and disconnect the connector.

NOTICE:

Do not push down the part (A) shown in the illustration when disconnecting the connector.




i.

Disconnect each connector and disengage each clamp under the front seat assembly.


j.
B564723

Remove the front seat assembly.

NOTICE:

Be careful not to damage the vehicle body.