Home › Vehicle Interior › SEAT › LUMBAR SUPPORT ADJUSTER ASSEMBLY › 2020.02–2020.11
RM37A0E _58 Vehicle Interior _086894 SEAT _0416494 LUMBAR SUPPORT ADJUSTER ASSEMBLY A

SEAT  LUMBAR SUPPORT ADJUSTER ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during lumbar support adjuster assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
·

Reclining motor (separate type front seatback spring assembly (driver seat))*

·

Slide motor (separate type front seat cushion spring assembly (driver seat))*


Initialize position control ECU Front Power Seat Control System (w/ Memory) (Click here)

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
·

Reclining motor (separate type front seatback spring assembly (driver seat))*

·

Slide motor (separate type front seat cushion spring assembly (driver seat))*


Initialize position control ECU Front Power Seat Control System (w/ Memory) (Click here)

CAUTION:
B543257

Wear protective gloves. Sharp areas on the parts may injure your hands.


NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 71074S 3.DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER

Hide 71868N 4.REMOVE FRONT SEAT FRONT CUSHION SHIELD

Hide 71812D 5.REMOVE FRONT SEAT CUSHION SHIELD

Hide 71862 6.REMOVE FRONT SEAT INNER CUSHION SHIELD

Hide 7.REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY

Hide 71930A 8.REMOVE FRONT SEAT HEADREST SUPPORT ASSEMBLY

Hide 9.REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD

Hide 85867A 10.REMOVE SEATBACK CLIMATE CONTROL BLOWER (w/ Climate Control Seat System)

Hide 72760D 11.REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY

a.
B544494

Disengage the clamp.


b.

Disconnect the 2 connectors.


c.
B520284

Disengage the 2 claws to remove the 2 front No. 2 seatback edge protectors from the front seatback frame sub-assembly.


d.
B536626C02
0,0 0,0 false
V113147

Remove in this Direction


Remove the lumbar support adjuster assembly from the front seatback frame sub-assembly as shown in the illustration.


e.

Remove the seatback felt from the lumbar support adjuster assembly.


Hide 71588 12.REMOVE FRONT NO. 2 SEATBACK EDGE PROTECTOR