Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model)
RM37A0E _57 Power Source / Network _086883 NETWORKING _0416014 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Communication stop for "ECM (Engine)" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

ECM main line or connector

·

ECM branch line or connector

·

Power source circuit of ECM

·

ECM ground circuit

·

ECM



WIRING DIAGRAM

C427156E02
0.406,1.188 4.688,1.385 4.281,0.198 10 false No. 2 Global CAN Junction Connector 0.51,2.635 3.313,2.875 2.802,0.24 10 false No. 1 Global CAN Junction Connector 0.115,1.177 0.5,1.427 0.385,0.25 10 false H90 1.781,0.24 2.167,0.49 0.385,0.25 10 false 4 1.75,0.823 2.135,1.073 0.385,0.25 10 false 14 5.5,0.208 5.885,0.458 0.385,0.25 10 false 7 5.458,0.802 5.844,1.052 0.385,0.25 10 false 17 5.729,0.323 6.188,0.552 0.458,0.229 10 false CAN+ 5.719,0.917 6.177,1.146 0.458,0.229 10 false CAN- 5.51,1.667 5.896,1.917 0.385,0.25 10 false 8 5.448,2.24 5.833,2.49 0.385,0.25 10 false 18 5.719,1.677 6.177,1.906 0.458,0.229 10 false CANH 5.719,2.49 6.177,2.719 0.458,0.229 10 false CANL 0.177,2.635 0.563,2.885 0.385,0.25 10 false A77 1.792,1.656 2.177,1.906 0.385,0.25 10 false 9 1.771,2.281 2.156,2.531 0.385,0.25 10 false 20 5.74,2.927 6.198,3.156 0.458,0.229 10 false IGSW 5.75,3.646 6.208,3.875 0.458,0.229 10 false +B 5.75,4.115 6.208,4.344 0.458,0.229 10 false +B2 5.729,4.75 6.188,4.979 0.458,0.229 10 false MREL 5.729,5.604 6.188,5.833 0.458,0.229 10 false E1 3.99,2.792 4.99,3.073 1,0.281 10 false ECU-IG2 NO. 1 5.5,2.813 5.729,3.083 0.229,0.271 10 false 2 5.5,3.531 5.729,3.802 0.229,0.271 10 false 9 5.448,4.01 5.677,4.281 0.229,0.271 10 false 35 5.438,4.625 5.667,4.896 0.229,0.271 10 false 15 5.448,5.469 5.677,5.74 0.229,0.271 10 false 10 5.688,6.177 6.156,6.417 0.469,0.24 10 false A27 1.646,2.927 3.573,3.313 1.927,0.385 10 false from IG2 NO. 1 Relay 1.281,3.667 3.208,4.052 1.927,0.385 10 false from EFI-MAIN NO. 1 Relay 1.396,4.729 3.323,5.115 1.927,0.385 10 false to EFI-MAIN NO. 1 Relay 6.021,6.177 6.49,6.417 0.469,0.24 10 false ECM

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (ECM MAIN LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A27 ECM connector.


c.
C381742C29
1.542,0.104 1.938,0.333 0.396,0.229 2.188,2.958 2.021,2.958 2.021,2.958 2.021,1.458 true 2.177,0.438 2.01,0.438 2.01,0.438 2.01,1.271 true 1.615,0.135 2.073,0.333 0.458,0.198 10 false A27 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 2.25,0.365 2.708,0.563 0.458,0.198 10 false CANH 2.26,2.896 2.719,3.094 0.458,0.198 10 false CANL
*a Front view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-8 (CANH) - A27-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

2.CHECK FOR OPEN IN CAN BUS LINES (ECM BRANCH LINE)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (ECM)

2.CHECK FOR OPEN IN CAN BUS LINES (ECM BRANCH LINE)
a.
C381742C30
1.542,0.104 1.938,0.333 0.396,0.229 1.74,2.958 1.906,2.958 1.906,2.958 1.906,1.458 true 1.74,0.438 1.906,0.438 1.906,0.438 1.906,1.271 true 1.615,0.135 2.073,0.333 0.458,0.198 10 false A27 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 1.323,0.375 1.781,0.573 0.458,0.198 10 false CAN+ 1.302,2.896 1.76,3.094 0.458,0.198 10 false CAN-
*a Front view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-7 (CAN+) - A27-17 (CAN-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK ECM POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (ECM)

3.CHECK ECM POWER SOURCE CIRCUIT

Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)