Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model)
RM37A0E _57 Power Source / Network _086883 NETWORKING _0416014 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Power Back Door ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Power Back Door ECU Communication Stop Mode Communication stop for "Back Door" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Multiplex network door ECU branch line or connector

·

Power source circuit of multiplex network door ECU

·

Multiplex network door ECU ground circuit

·

Multiplex network door ECU



WIRING DIAGRAM

C427500E01
5.25,4.927 7.01,5.313 1.76,0.385 10 false Multiplex Network Door ECU 0.521,1.885 3.208,2.198 2.688,0.313 10 false No. 9 Global CAN Junction Connector 0.177,1.885 0.677,2.156 0.5,0.271 10 false M96 5.708,0.969 6.292,1.198 0.583,0.229 10 false CANP 5.729,1.5 6.313,1.729 0.583,0.229 10 false CANN 5.729,2.323 6.031,2.552 0.302,0.229 10 false B 5.729,2.938 6.313,3.167 0.583,0.229 10 false IG 5.729,3.583 6.313,3.813 0.583,0.229 10 false ECUB 5.719,4.26 6.302,4.49 0.583,0.229 10 false GND 5.354,0.75 5.656,0.979 0.302,0.229 10 false 39 5.354,1.281 5.656,1.51 0.302,0.229 10 false 40 5.396,2.094 5.698,2.323 0.302,0.229 10 false 1 5.344,2.719 5.646,2.948 0.302,0.229 10 false 18 5.354,3.365 5.656,3.594 0.302,0.229 10 false 20 5.365,4.042 5.667,4.271 0.302,0.229 10 false 10 3.969,3.438 5.188,3.708 1.219,0.271 10 false ECU-B NO. 2 1.74,3.563 3.365,3.813 1.625,0.25 10 false from Auxiliary Battery 3.865,2.802 5.083,3.073 1.219,0.271 10 false ECU-IG1 NO. 4 4.281,2.156 5.021,2.417 0.74,0.26 10 false PBD 1.781,2.271 3.406,2.521 1.625,0.25 10 false from Auxiliary Battery 1.833,2.917 3.646,3.292 1.813,0.375 10 false from IG1-NO.1 Relay 1.625,1.354 1.927,1.583 0.302,0.229 10 false 7 1.615,0.823 1.917,1.052 0.302,0.229 10 false 1 5.292,4.26 5.688,4.49 0.396,0.229 10 false W19 5.292,3.583 5.688,3.813 0.396,0.229 10 false W18 5.302,2.948 5.698,3.177 0.396,0.229 10 false W18 5.292,1.5 5.688,1.729 0.396,0.229 10 false W18 5.281,0.969 5.677,1.198 0.396,0.229 10 false W18 5.281,2.292 5.677,2.521 0.396,0.229 10 false W19

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (MULTIPLEX NETWORK DOOR ECU BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the W18 multiplex network door ECU connector.


c.
C427501C01
1.417,0.375 1.875,0.635 0.458,0.26 2.927,2.958 3.094,2.958 3.094,2.958 3.094,2.125 true 2.781,2.698 2.948,2.698 2.948,2.698 2.948,2.115 true 0.115,0.146 0.427,0.344 0.313,0.198 10 false *a 1.51,0.427 1.823,0.625 0.313,0.198 10 false W18 2.323,2.625 2.792,2.833 0.469,0.208 10 false CANP 2.448,2.896 2.917,3.104 0.469,0.208 10 false CANN
*a Front view of wire harness connector
(to Multiplex Network Door ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W18-39 (CANP) - W18-40 (CANN) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (MULTIPLEX NETWORK DOOR ECU)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the W19 multiplex network door ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

C427517C01
0.49,0.844 0.938,1.094 0.448,0.25 3.115,0.875 3.563,1.125 0.448,0.25 2.229,1.115 2.229,1.448 2.229,1.448 2.396,1.448 true 1.531,0.823 1.531,0.406 1.531,0.406 1.365,0.406 true 6.229,0.917 6.229,0.25 6.229,0.25 6.396,0.25 true 5.99,0.917 5.99,0.25 5.99,0.25 5.823,0.25 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 0.573,0.885 0.938,1.115 0.365,0.229 10 false W19 3.198,0.906 3.563,1.135 0.365,0.229 10 false W18 2.49,1.365 2.938,1.594 0.448,0.229 10 false GND 1.198,0.333 1.646,0.563 0.448,0.229 10 false B 5.625,0.177 6.073,0.406 0.448,0.229 10 false IG 6.479,0.188 6.927,0.417 0.448,0.229 10 false ECUB
*a Front view of wire harness connector
(to Multiplex Network Door ECU)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
W19-10 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
W18-18 (IG) - Body ground Ignition switch ON 11 to 14 V
W18-20 (ECUB) - Body ground Ignition switch off 11 to 14 V
W19-1 (B) - Body ground Ignition switch off 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)