Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model)
RM37A0E _57 Power Source / Network _086883 NETWORKING _0416014 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Motor Generator Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Motor Generator Control ECU Communication Stop Mode Communication stop for "Motor Generator" and/or "Rear Motor Generator" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Inverter with converter assembly branch line or connector

·

Power source circuit of inverter with converter assembly

·

Inverter with converter assembly ground circuit

·

Inverter with converter assembly



WIRING DIAGRAM

C427507E03
5.615,6.188 6.979,6.708 1.365,0.521 10 false Inverter with Converter Assembly 0.469,2.896 3.115,3.281 2.646,0.385 10 false No. 1 Global CAN Junction Connector 0.146,2.896 0.76,3.188 0.615,0.292 10 false A77 1.771,0.615 2.385,0.906 0.615,0.292 10 false 10 1.771,1.219 2.385,1.51 0.615,0.292 10 false 21 5.354,0.615 5.969,0.906 0.615,0.292 10 false 24* 5.354,1.208 5.969,1.5 0.615,0.292 10 false 33* 5.677,0.729 6.292,1.021 0.615,0.292 10 false CNH2 5.688,1.323 6.302,1.615 0.615,0.292 10 false CNL2 5.729,3.479 6.344,3.771 0.615,0.292 10 false +B2 5.719,4.156 6.333,4.448 0.615,0.292 10 false +B 5.698,4.719 6.313,5.01 0.615,0.292 10 false IGCT 5.698,5.448 6.313,5.74 0.615,0.292 10 false GND1 5.438,3.365 6.052,3.656 0.615,0.292 10 false 35 5.438,4.021 6.052,4.313 0.615,0.292 10 false 36 5.427,4.615 6.042,4.906 0.615,0.292 10 false 26 5.49,5.302 6.104,5.594 0.615,0.292 10 false 9 5.292,6.198 5.906,6.49 0.615,0.292 10 false A55 1.708,3.479 3.406,3.813 1.698,0.333 10 false from IGCT Relay 4.115,3.365 5.344,3.646 1.229,0.281 10 false PCU 3.896,4.604 5.125,4.885 1.229,0.281 10 false IGCT NO. 3 0.99,5.292 2.688,5.625 1.698,0.333 10 false *: for 4WD/AWD 5.677,1.958 6.292,2.25 0.615,0.292 10 false CANH 5.698,2.552 6.313,2.844 0.615,0.292 10 false CANL 5.417,2.427 6.031,2.719 0.615,0.292 10 false 31 5.417,1.844 6.031,2.135 0.615,0.292 10 false 22 1.75,2.438 2.365,2.729 0.615,0.292 10 false 22 1.75,1.854 2.365,2.146 0.615,0.292 10 false 11

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (INVERTER WITH CONVERTER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A55 inverter with converter assembly connector.


c.
C427508C01
1.479,0.25 1.896,0.51 0.417,0.26 1.385,1.917 1.385,0.667 1.385,0.667 1.219,0.667 true 1.385,2.094 1.385,3.177 1.385,3.177 1.219,3.177 true 1.667,1.917 1.667,0.667 1.667,0.667 1.833,0.667 true 1.656,2.094 1.656,3.177 1.656,3.177 1.823,3.177 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 1.917,0.583 2.563,0.813 0.646,0.229 10 false CNH2*A 0.823,3.104 1.344,3.354 0.521,0.25 10 false CANL 1.563,0.302 2,0.5 0.438,0.198 10 false A55 0.802,0.594 1.24,0.792 0.438,0.198 10 false CANH 1.906,3.104 2.594,3.333 0.688,0.229 10 false CNL2*A
*A for 4WD/AWD
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-22 (CANH) - A55-31 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω

for 4WD/AWD
Tester Connection Condition Specified Condition
A55-24 (CNH2) - A55-33 (CNL2) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C427508C02
1.479,0.177 1.896,0.438 0.417,0.26 2.042,1.656 2.042,0.74 2.042,0.74 2.188,0.74 true 2.219,3.094 2.052,3.094 2.052,3.094 2.052,2.094 true 1.75,3.094 1.917,3.094 1.917,3.094 1.917,2.094 true 1.917,1.917 1.917,0.583 1.917,0.583 1.75,0.583 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 1.438,3.01 1.875,3.208 0.438,0.198 10 false +B2 1.385,0.5 1.823,0.698 0.438,0.198 10 false IGCT 1.563,0.208 2,0.406 0.438,0.198 10 false A55 2.313,3.01 2.75,3.208 0.438,0.198 10 false +B 2.271,0.667 2.708,0.865 0.438,0.198 10 false GND1
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-9 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A55-26 (IGCT) - Body ground Ignition switch ON 11 to 14 V
A55-35 (+B2) - Body ground Ignition switch ON 11 to 14 V
A55-36 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)