Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › 2020.02–2020.11
RM37A0E _59 Vehicle Exterior _086899 WINDOW / GLASS _0416694 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during windshield glass sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

·

Forward recognition camera

·

Windshield glass*


Adjust forward recognition camera
·

Dynamic Radar Cruise Control System (for HV model)

·

Front Camera System

·

Lane Control System

·

Road Sign Assist System

·

Pre-collision System

·

Lighting System (EXT)


One Time Recognition:(Click here)
or
Sequential Recognition:(Click here)

NOTICE:

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, front camera system, lane control system, road sign assist system, pre-collision system, lighting system (EXT) may not operate properly due to a difference in the transmissivity or black ceramic border.


Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

·

Forward recognition camera

·

Windshield glass*


Adjust forward recognition camera
·

Dynamic Radar Cruise Control System (for Gasoline model)

·

Front Camera System

·

Lane Control System

·

Road Sign Assist System

·

Pre-collision System

·

Lighting System (EXT)


One Time Recognition:(Click here)
or
Sequential Recognition:(Click here)

NOTICE:

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, front camera system, lane control system, road sign assist system, pre-collision system, lighting system (EXT) may not operate properly due to a difference in the transmissivity or black ceramic border.


PROCEDURE

Hide 55708 1.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 75534 2.REMOVE WINDSHIELD OUTSIDE MOULDING LH

Hide 75533 3.REMOVE WINDSHIELD OUTSIDE MOULDING RH

HINT:

Use the same procedure as for the LH side.


Hide 8646C 5.REMOVE FORWARD RECOGNITION CAMERA

Hide 88620E 6.REMOVE AIR CONDITIONING THERMISTOR ASSEMBLY

Hide 89941 7.REMOVE RAIN SENSOR (w/ Rain Sensor)

Hide 81260A 8.REMOVE MAP LIGHT ASSEMBLY

Hide 62212B 9.REMOVE FRONT PILLAR GARNISH ASSEMBLY LH

Hide 62211U 10.REMOVE FRONT PILLAR GARNISH ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 74610A 11.REMOVE ASSIST GRIP SUB-ASSEMBLY

Hide 74325 12.REMOVE VISOR BRACKET COVER (for LH Side)

Hide 74320 13.REMOVE VISOR ASSEMBLY LH

Hide 74325 14.REMOVE VISOR BRACKET COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 74310 15.REMOVE VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 17.SEPARATE ROOF HEADLINING ASSEMBLY

a.

Disconnect the connector.


b.

Slightly lower the front section of the roof headlining assembly so that the windshield glass can be removed.

NOTICE:

Do not damage the roof headlining assembly or vehicle interior.


HINT:

It is not necessary to completely remove the roof headlining assembly.



Hide 18.REMOVE WINDSHIELD GLASS SUB-ASSEMBLY

a.

w/ Windshield Deicer System:

i.

Disconnect the connector.



b.
B564598C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the area around the installation position of the windshield glass sub-assembly on the vehicle body to prevent it from being scratched.


c.
B564599C01
0.552,0.24 1.406,0.604 true 2.49,0.865 2.833,1.188 true 2.333,1.271 2.677,1.594 true 0.375,0.135 0.688,0.292 0.313,0.156 10 false *1 2.854,1.083 3.167,1.24 0.313,0.156 10 false *2 2.719,1.552 3.031,1.708 0.313,0.156 10 false *a
*1 Windshield Glass
*2 Windshield Outside Upper Moulding
*a Cut


Using a knife, cut off the windshield outside upper moulding as shown in the illustration.


d.
B564600C01
1.313,1.667 1.313,1 1.313,1 1.646,1 true 1.313,1.167 1.646,1.167 true 1.24,1.688 1.5,1.896 0.26,0.208 10 true *a
*a Matchmark


Place matchmarks on the windshield glass sub-assembly and vehicle body at the locations indicated in the illustration.

HINT:

Matchmarks are not necessary if the windshield glass is not going to be reused.



e.

When using a windshield knife:

i.

Apply soapy water to the area around the adhesive.


ii.
B567003C01
0.604,4 1.198,3.49 true 2.427,3.167 2.875,2.76 2.875,2.76 2.563,3.24 true 0.438,3.958 0.75,4.115 0.313,0.156 10 false *a 2.906,2.646 3.219,2.802 0.313,0.156 10 false *b
*a Windshield Knife
*b Aligned with Windshield Glass Sub-assembly
V100135

Pull


Insert a windshield knife into the adhesive between the windshield glass sub-assembly and vehicle body.


iii.

While keeping the windshield knife perpendicular to the outer surface of the windshield glass sub-assembly, cut the adhesive by pulling the windshield knife around the windshield glass sub-assembly.

NOTICE:
·

Do not pry the windshield glass sub-assembly with the windshield knife.

·

Do not use a windshield knife to cut the adhesive on the lower side of the windshield glass sub-assembly.

·

When separating the windshield glass sub-assembly, be careful not to damage the paint or interior and exterior ornaments.



HINT:

Insert the windshield knife in an area where the gap between windshield glass sub-assembly and vehicle body is large.




f.

When using piano wire:

i.
B564601C01
2.219,0.5 1.677,0.979 1.677,0.979 1.156,0.5 true 0.427,0.25 0.604,0.51 true 1.594,1.021 1.833,1.208 0.24,0.188 10 true *1 0.188,0.167 0.406,0.365 0.219,0.198 10 true *a
*1 Windshield Glass Stopper
*a Piano Wire


Pass a piano wire between the vehicle body and windshield glass sub-assembly from the interior.


ii.

Tie both wire ends to wooden blocks or similar objects that can serve as handles.


iii.

Cut the adhesive by pulling the piano wire around the windshield glass sub-assembly.

NOTICE:
·

When separating the windshield glass sub-assembly, be careful not to damage the paint or interior and exterior ornaments.

·

To prevent the safety pad from being scratched when removing the windshield glass sub-assembly, place a plastic sheet between the piano wire and safety pad.





g.

Disengage the windshield glass stoppers.

B564602C01
2.198,0.979 1.948,0.896 true 5.448,0.646 5.042,0.417 true 5.323,0.875 5.323,1.021 5.323,1.021 5.792,1.021 true 5.573,1.021 5.573,0.865 true 5.469,1.021 5.469,0.802 true 0.167,0.083 0.583,0.333 0.417,0.25 12 false *A 3.917,0.083 4.333,0.333 0.417,0.25 12 false *B 2.229,0.896 2.542,1.052 0.313,0.156 10 false *1 4.854,0.333 5.167,0.49 0.313,0.156 10 false *2 5.813,0.927 6.125,1.083 0.313,0.156 10 false *1
*A for 1-piece Type *B for 2-piece Type
*1 No. 1 Windshield Glass Stopper *2 No. 2 Windshield Glass Stopper


NOTICE:
·

The No. 1 windshield glass stoppers and No. 2 windshield glass stoppers are installed to the windshield glass sub-assembly as shown in the illustration. Be careful not to damage the windshield glass sub-assembly when cutting the adhesive.

·

To prevent the windshield glass sub-assembly from falling when performing this operation, be sure to hold the windshield glass sub-assembly using suction cups.



HINT:

Depending on the vehicle, either 1-piece type or 2-piece type stoppers may be present.



h.

Using suction cups, remove the windshield glass sub-assembly.

NOTICE:
·

Be careful not to drop the windshield glass sub-assembly.

·

Leave as much adhesive on the vehicle body as possible when removing the windshield glass sub-assembly.




Hide 56117A 19.REMOVE WINDOW GLASS ADHESIVE DAM

a.

When reusing the windshield glass:

i.
B564603C01
0.073,0.073 0.5,0.438 0.427,0.365 12 false *A
*A Back Side


Using a scraper, remove the 2 window glass adhesive dams.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the window glass adhesive dam with a new ones.




ii.
B564604C01
0.073,0.073 0.5,0.438 0.427,0.365 12 false *A
*A Back Side


Using a scraper, remove the window glass adhesive dam.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the window glass adhesive dam with a new ones.





Hide 75531F 20.REMOVE WINDSHIELD OUTSIDE UPPER MOULDING

a.

When reusing the windshield glass:

i.
B564605C01
0.073,0.073 0.469,0.375 0.396,0.302 12 false *A
*A Back Side


Using a scraper, remove the windshield outside upper moulding.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the windshield outside upper moulding with a new one.





Hide 21.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 1-piece Type)

a.

When reusing the windshield glass:

i.
B564607C01
0.073,0.073 0.469,0.438 0.396,0.365 12 false *A
*A Back Side


Using a scraper, remove the 2 No. 1 windshield glass stoppers.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the 1-piece type No. 1 windshield glass stoppers with new 2-piece type No. 1 and No. 2 windshield glass stoppers.





Hide 56116C 22.REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.

When reusing the windshield glass:

i.
B564607C01
0.073,0.073 0.469,0.438 0.396,0.365 12 false *A
*A Back Side


Using a scraper, remove the 2 No. 2 windshield glass stoppers.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the No. 2 windshield glass stoppers with new ones.





Hide 56115A 23.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.
B564608

Remove the 2 No. 1 windshield glass stoppers from the vehicle body.

NOTICE:

Be sure to replace the No. 1 windshield glass stoppers with new ones.



Hide 56153C 24.REMOVE FRONT WINDOW INNER CENTER MOULDING

HINT:

Perform the following procedure only when replacement of the front window inner center moulding is necessary.


a.
B573488C01
1.573,2.458 1.573,2.375 1.573,2.375 1.99,2.375 false 1.906,2.458 1.906,2.375 false 0.073,0.073 0.573,0.469 0.5,0.396 12 false *A 2.031,2.313 2.344,2.469 0.313,0.156 10 false *a
*A Back Side
*a Matchmark


B564606C01
0.073,0.073 0.469,0.375 0.396,0.302 12 false *A
*A Back Side


Place matchmarks on the windshield glass at the locations indicated in the illustration.


b.

Using a scraper, remove the front window inner center moulding.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the front window inner center moulding with a new one.




Hide 25.CLEAN WINDSHIELD GLASS

a.

When reusing the windshield glass:

i.
B149736

Using a scraper, remove any remaining adhesive dam and adhesive residue from the windshield glass.

NOTICE:

Be careful not to damage the windshield glass.



ii.

Clean the outer circumference of the windshield glass with a non-residue solvent.

NOTICE:
·

Do not touch the windshield glass surface after cleaning it.

·

Even if using a new windshield glass, clean it with a non-residue solvent.





Hide 26.CLEAN VEHICLE BODY

a.

Clean and shape the contact surface of the vehicle body.

i.
B514552C01
0.365,0.844 0.833,1.125 false 0.198,0.74 0.51,0.896 0.313,0.156 10 false *a 1.917,1.25 2.229,1.406 0.313,0.156 10 false a
*a Vehicle Body
V100155

Adhesive


Using a knife, cut off any excess adhesive on the contact surface of the vehicle body as shown in the illustration.

Standard Dimension:
Area Dimension
a 1.0 mm (0.0394 in.) or more


NOTICE:

Be careful not to damage the vehicle body.


HINT:

Leave approximately 1.0 mm (0.0394 in.) of adhesive on the vehicle body.



ii.

Clean the contact surface of the vehicle body with a piece of cloth saturated with non-residue solvent.

HINT:

Even if all of the adhesive has been removed, clean the vehicle body.