58410B
1.REMOVE DECK BOARD ASSEMBLY
Remove the deck board assembly.
58409A
2.REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY (w/o Woofer)
Remove the No. 3 deck board sub-assembly.
64910J
3.REMOVE TONNEAU COVER ASSEMBLY
Remove the tonneau cover assembly.
58441L
4.REMOVE BATTERY SERVICE HOLE COVER
Disengage the 6 claws and 2 guides to remove the battery service hole cover.
64993
5.REMOVE REAR DECK FLOOR BOX
Using a clip remover, remove the 7 clips.
Remove the nut.
Disengage the 7 claws and 2 clips to remove the rear deck floor box.
64742C
6.REMOVE DECK SIDE TRIM BOX LH (w/o Woofer)
Disengage the 4 claws to remove the deck side trim box LH.
58387B
7.REMOVE REAR FLOOR FINISH PLATE
|
Remove in this Direction |
Disengage the 4 claws, 2 guides and 4 clips to remove the rear floor finish plate as shown in the illustration.
8.REMOVE REAR NO. 2 SEAT ASSEMBLY
67914
9.REMOVE FRONT DOOR SCUFF PLATE LH
|
Place Hand Here |
|
Remove in this Direction |
Disengage the claw as shown in the illustration.
Use the same procedure for the front side and rear side.
|
Place Hand Here |
|
Remove in this Direction |
Disengage the claw and guide as shown in the illustration.
|
Place Hand Here |
|
Remove in this Direction |
Disengage the 2 claws as shown in the illustration.
|
Place Hand Here |
|
Remove in this Direction |
Disengage the 2 claws as shown in the illustration.
|
Place Hand Here |
|
Remove in this Direction |
Disengage the 2 claws as shown in the illustration.
|
Place Hand Here |
|
Remove in this Direction |
Disengage the 2 guides to remove the front door scuff plate LH as shown in the illustration.
62112A
10.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
|
Remove in this Direction |
Remove the clip.
Disengage the claw and clip to remove the cowl side trim sub-assembly LH as shown in the illustration.
62312B
11.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
62212B
12.REMOVE FRONT PILLAR GARNISH ASSEMBLY LH
|
Protective Tape |
Apply protective tape around the front pillar garnish assembly LH as shown in the illustration.
|
Remove in this Direction |
Pull the upper part of the front pillar garnish assembly LH toward the inside of the cabin as shown in the illustration to disengage the front pillar garnish assembly LH from the base of the 2 front pillar garnish clips.
Let the front pillar garnish assembly LH hang from the 2 front pillar garnish clips.
| *1 | Front Pillar Garnish Clip |
While pushing the tabs of the front pillar garnish clip as shown in the illustration, disengage it.
When the front pillar garnish clip cannot be disengaged easily:
|
Move in this Direction |
While pushing the tab of the front pillar garnish clip shown in the illustration with your finger, move the front pillar garnish clip in the direction shown in the illustration.
|
Pull in this Direction |
While pulling the front pillar garnish clip as shown in the illustration, push the tab of the front pillar garnish clip shown in the illustration with a screwdriver and disengage the front pillar garnish clip.
|
Remove in this Direction |
Disengage the 2 guides to remove the front pillar garnish assembly LH as shown in the illustration.
w/ Front No. 3 Speaker:
Disconnect the connector.
| *1 | Curtain Shield Airbag Assembly LH |
| *a | Protective Cover |
| *b | Adhesive Tape |
Protect the curtain shield airbag assembly LH.
Cover the curtain shield airbag assembly LH with a protective cover, such as a cloth, and secure the edges of the cover with tape as shown in the illustration.
Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish assembly LH is removed.
72138M
13.REMOVE REAR OUTER SEAT TRACK BRACKET COVER LH
Operate the seat track adjusting handle and move the rear No. 1 seat assembly LH to the foremost position.
Disengage the 6 clips and 2 guides to remove the rear outer seat track bracket cover LH.
67918A
14.REMOVE REAR DOOR SCUFF PLATE LH
|
Place Hand Here |
|
Remove in this Direction |
Disengage the claw as shown in the illustration.
Disengage the 4 claws, 3 clips and guide to remove the rear door scuff plate LH.
62332C
15.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
73233
16.REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)
73220
17.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
62414A
18.REMOVE LOWER CENTER PILLAR GARNISH LH
| *a | Claw (A) |
| *b | Claw (B) |
|
Place Hand Here |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Pull the lower center pillar garnish LH in the directions indicated by the arrows (1) shown in the illustration to disengage the 2 claws (A).
Pull the lower center pillar garnish LH in the direction indicated by the arrow (2) shown in the illustration to disengage the 2 claws (B).
|
Remove in this Direction |
Disengage the 2 clips to remove the lower center pillar garnish LH as shown in the illustration.
62420A
19.REMOVE CENTER PILLAR GARNISH ASSEMBLY LH
Using a clip remover, remove the 2 clips.
Disengage the guide.
|
Remove in this Direction |
Disengage the clip and 2 guides as shown in the illustration.
Pass the anchor of the front seat outer belt assembly LH through the center pillar garnish assembly LH and remove the center pillar garnish assembly LH.
67913
20.REMOVE FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
62111A
21.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
62311B
22.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
62211U
23.REMOVE FRONT PILLAR GARNISH ASSEMBLY RH
Use the same procedure as for the LH side.
72137S
24.REMOVE REAR OUTER SEAT TRACK BRACKET COVER RH
Use the same procedure as for the LH side.
67917A
25.REMOVE REAR DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
62331C
26.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
73233
27.REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)
Use the same procedure as for the LH side.
73210
28.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
62413A
29.REMOVE LOWER CENTER PILLAR GARNISH RH
Use the same procedure as for the LH side.
62411
30.REMOVE CENTER PILLAR GARNISH ASSEMBLY RH
Use the same procedure as for the LH side.
64713F
31.REMOVE FRONT DECK SIDE TRIM COVER LH
Remove the clip.
Disengage the 5 clips and 3 guides to remove the front deck side trim cover LH as shown in the illustration.
73370E
32.DISCONNECT REAR SEAT OUTER BELT ASSEMBLY LH
64715E
33.REMOVE NO. 2 DECK SIDE TRIM COVER
|
Remove in this Direction |
Disengage the 4 claws and clip to remove the No. 2 deck side trim cover as shown in the illustration.
73570
34.DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH
64974
35.REMOVE DECK TRIM POCKET COVER (for LH Side)
Using a moulding remover, disengage the 2 claws to remove the deck trim pocket cover.
64725F
36.REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for LH Side)
|
Remove in this Direction |
Turn the No. 1 luggage compartment trim hook as shown in the illustration to remove it.
66311
37.REMOVE ROPE HOOK (for LH Side)
|
Remove in this Direction |
Using a moulding remover, disengage the 4 claws as shown in the illustration.
Remove the 2 bolts and 2 rope hooks.
64740C
38.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
Remove the 3 bolts.
Disengage the claw, 10 clips, and 5 guides to remove the deck trim side panel assembly LH.
62639A
39.REMOVE QUARTER PILLAR GARNISH LH
Disengage the claw, 2 clips and guide.
Pass the anchor of the rear seat outer belt assembly LH through the quarter pillar garnish LH and remove the quarter pillar garnish LH.
62480A
40.REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH
|
Remove in this Direction |
Disengage the 2 clips to disconnect the inner roof side garnish assembly LH as shown in the illustration.
| *1 | Roof Side Garnish Clip |
While pushing the tabs of the roof side garnish clip as shown in the illustration, disengage it.
When the roof side garnish clip cannot be disengaged easily:
|
Move in this Direction |
While pushing the tab of the roof side garnish clip shown in the illustration with your finger, move the roof side garnish clip in the direction shown in the illustration.
|
Pull in this Direction |
While pulling the roof side garnish clip as shown in the illustration, push the tab of the roof side garnish clip shown in the illustration with a screwdriver and disengage the roof side garnish clip.
|
Remove in this Direction |
Disengage the 6 clips as shown in the illustration.
Pass the anchor of the rear No. 2 seat outer belt assembly LH through the inner roof side garnish assembly LH and remove the inner roof side garnish assembly LH.
64712F
41.REMOVE FRONT DECK SIDE TRIM COVER RH
Remove the clip.
Disengage the 5 clips and 2 guides to remove the front deck side trim cover LH as shown in the illustration.
73360D
42.DISCONNECT REAR SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
64714H
43.REMOVE NO. 1 DECK SIDE TRIM COVER
Use the same procedure as for the No. 2 deck side trim cover.
73560
44.DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
88625T
45.REMOVE COOLER (NO. 2 ROOM TEMP. SENSOR) THERMISTOR
64974
46.REMOVE DECK TRIM POCKET COVER (for RH Side)
Use the same procedure as for the LH side.
64725F
47.REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side)
Use the same procedure as for the LH side.
66311
48.REMOVE ROPE HOOK (for RH Side)
Use the same procedure as for the LH side.
64730B
49.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
Remove the 3 bolts.
Disengage the claw, 10 clips, and 5 guides to remove the deck trim side panel assembly RH.
62638A
50.REMOVE QUARTER PILLAR GARNISH RH
Use the same procedure as for the LH side.
62470A
51.REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH
Use the same procedure as for the LH side.
89943
52.REMOVE RAIN SENSOR COVER (w/ Rain Sensor)
86466E
53.REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Pre-collision System)
86466D
54.REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Pre-collision System)
81260A
55.REMOVE MAP LIGHT ASSEMBLY
81360T
56.REMOVE SPOT LIGHT ASSEMBLY (except Panoramic Moon Roof)
81240
57.REMOVE NO. 1 ROOM LIGHT ASSEMBLY
86295
58.REMOVE TELEVISION BASE (w/ Rear Seat Entertainment System)
86680A
59.REMOVE TELEVISION DISPLAY ASSEMBLY (w/ Rear Seat Entertainment System)
88892Q
60.REMOVE COOLER PLATE
87217D
61.REMOVE REAR NO. 1 SIDE AIR DUCT
74610A
62.REMOVE ASSIST GRIP SUB-ASSEMBLY
Use the same procedure for all assist grip sub-assemblies.
| *a | Cutout |
Insert SST into the cutout of the assist grip cover LH as shown in the illustration.
To prevent the assist grip sub-assembly from being damaged, make sure to insert SST straight into the cutout.
| *a | 30 to 45° |
|
Pull in this Direction |
Pull SST as shown in the illustration to disengage the claw.
To prevent the assist grip sub-assembly from being damaged, make sure to only pull SST as shown in the illustration.
Use the same procedure for the claw on the other side of the assist grip cover LH.
Use the same procedure for the LH side and RH side.
Remove the assist grip cover LH.
Use the same procedure for the LH side and RH side.
|
Remove in this Direction |
Disengage the 2 clips as shown in the illustration to remove the assist grip sub-assembly.
Remove the 2 clips from the vehicle body.
74630E
63.REMOVE REAR ASSIST GRIP ASSEMBLY LH
Use the same procedure as for the assist grip sub-assembly.
74620C
64.REMOVE REAR ASSIST GRIP ASSEMBLY RH
Use the same procedure as for the assist grip sub-assembly.
74325
65.REMOVE VISOR BRACKET COVER LH (w/ Cover)
Using a moulding remover, disengage the 4 claws and remove the visor bracket cover LH.
74320
66.REMOVE VISOR ASSEMBLY LH
Using a T25 "TORX" socket wrench, remove the 2 screws and visor assembly LH.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Pull the visor assembly LH in the direction indicated by the arrow (1) shown in the illustration to disconnect it from the visor holder.
Pull the visor assembly LH in the direction indicated by the arrow (2) shown in the illustration to remove it.
74325
67.REMOVE VISOR BRACKET COVER RH (w/ Cover)
Use the same procedure as for the LH side.
74310
68.REMOVE VISOR ASSEMBLY RH
Use the same procedure as for the LH side.
74348
69.REMOVE VISOR HOLDER
Use the same procedure for the LH side and RH side.
| *a | 45° |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Turn the visor holder approximately 45° and remove it as indicated by the arrows, in the order shown in the illustration.
Disengage the 2 claws to remove the base of each visor holder.
70.REMOVE ROOF HEADLINING ASSEMBLY
for Windshield Glass Side:
Disconnect each connector.
for Front Pillar LH Side:
Disengage the 4 clamps.
Disconnect the 3 connectors.
Disconnect the washer hose assembly.
Use a container to collect the windshield washer fluid.
for Front Pillar RH Side:
| *a | Clamp |
| *b | Guide |
Disengage the 3 clamps.
Disconnect the 3 connectors.
Remove the bolt.
Disengage the guide.
for Rear Pillar LH Side with Digital Audio Broadcasting Antenna:
| *a | Clamp |
| *b | Guide |
Disconnect the connector.
Remove the bolt.
Disengage the guide.
Disengage the 3 clamps.
for Rear Pillar LH Side:
Disconnect the connector.
Disconnect the washer hose assembly.
Use a container to collect the windshield washer fluid.
for Normal Roof:
Remove the 6 clips.
for Moon Roof:
Disconnect the connector.
Disengage the 11 fasteners.
Remove the 4 clips.
for Panoramic Moon Roof:
Disconnect the connector.
Disengage the 20 fasteners.
Remove the 2 clips.
Disconnect the 2 connectors.
|
Remove in this Direction |
Remove the roof headlining assembly from the vehicle through the back door as shown in the illustration.
Do not damage the roof headlining assembly or vehicle interior.