Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS
RM37A0E _59 Vehicle Exterior _086899 WINDOW / GLASS _0416695 BACK DOOR GLASS A

WINDOW / GLASS  BACK DOOR GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

Make sure to use Toyota Genuine Windshield Glass Adhesive (High Modulus Type) or an equivalent high modulus adhesive.

·

After cutting off the old adhesive remaining on the adhesion surface, apply new adhesive within 2 hours.

·

If the cut surface of the old adhesive is left exposed for a long time, the adhesion strength will be reduced, so apply the new adhesive quickly.



PROCEDURE

Hide 62785F 1.INSTALL BACK DOOR GLASS SPACER

a.

Using a brush or sponge, coat the installation area of a new back door glass spacer with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.

Install the 3 back door glass spacers to the back door glass as shown in the illustration.

B594147C01
2.24,0.896 1.552,1.406 1.552,1.406 1.708,0.792 true 3.813,0.875 3.156,1.74 3.156,1.74 3.313,0.865 true 5.438,0.833 5.531,1.74 5.531,1.74 4.917,0.896 true 0.156,0.156 0.573,0.542 0.417,0.385 12 false *A 1.438,1.438 1.75,1.625 0.313,0.188 10 true *a 3.052,1.781 3.365,1.969 0.313,0.188 10 true *a 5.479,1.76 5.792,1.948 0.313,0.188 10 true *a
*A Back Side - -
*a Marking for Spacer Pasting - -



Hide 64827B 2.INSTALL BACK WINDOW GLASS CLIP

a.

Using a brush or sponge, coat the installation area of a new back window glass clip with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.

Install the back window glass clip to the back door glass as shown in the illustration.

B594145C01
3.333,1.385 2.792,1.615 2.792,1.615 3.396,0.813 true 3.802,0.844 4.625,0.698 4.625,0.698 3.844,1.375 true 0.135,0.177 0.583,0.563 0.448,0.385 12 false *A 2.615,1.656 2.896,1.906 0.281,0.25 10 true *a 4.635,0.594 4.917,0.844 0.281,0.25 10 true *a
*A Back Side - -
*a Marking for Clip Installation - -



Hide 75497B 3.INSTALL BACK WINDOW OUTSIDE MOULDING CLIP LH

a.

Using a brush or sponge, coat the installation area of a new back window outside moulding clip LH with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.

Install the back window outside moulding clip LH to the back door glass as shown in the illustration.

B594143C01
2.49,1.375 1.896,1.583 1.896,1.583 2.5,0.792 true 3.01,0.677 3.75,1.417 3.75,1.417 2.948,1.292 true 3.01,0.802 3.75,1.417 3.75,1.417 2.948,0.833 true 0.135,0.177 0.583,0.563 0.448,0.385 12 false *A 1.708,1.604 1.99,1.854 0.281,0.25 10 true *a 3.792,1.333 4.073,1.583 0.281,0.25 10 true *a
*A Back Side - -
*a Marking for Clip Installation - -



Hide 75496C 4.INSTALL BACK WINDOW OUTSIDE MOULDING CLIP RH

HINT:

Use the same procedure as for the LH side.


Hide 75573C 5.INSTALL BACK WINDOW OUTSIDE MOULDING

a.

Using a brush or sponge, coat the installation area of a new back window outside moulding with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.

Install the back window outside moulding to the back door glass as shown in the illustration.

B594148C01
1.24,0.781 1.51,0.583 false 5.781,0.635 5.917,0.802 false 0.25,0.115 0.677,0.438 0.427,0.323 12 false *A 1.531,0.479 1.844,0.635 0.313,0.156 10 false *a 5.615,0.521 5.927,0.677 0.313,0.156 10 false *a 3.906,1.771 4.063,1.969 0.156,0.198 10 false A 3.917,2.104 4.073,2.302 0.156,0.198 10 false A 5.219,1.49 5.552,1.719 0.333,0.229 10 false A-A 0.719,0.667 0.875,0.865 0.156,0.198 10 false a 6.344,0.667 6.5,0.865 0.156,0.198 10 false a 5.885,2.031 6.042,2.229 0.156,0.198 10 false b 6.219,2.031 6.375,2.229 0.156,0.198 10 false c
*A Back Side - -
*a Alignment Position (Edge Of Curved Surface) - -


Standard Dimension:
Area Dimension Area Dimension
a 3.0 mm (0.118 in.) b 11.6 mm (0.457 in.)
c 15.4 mm (0.606 in.) - -



Hide 68131 6.INSTALL BACK DOOR GLASS

NOTICE:
·

After cutting off the old adhesive remaining on the adhesion surface, apply new adhesive within 2 hours.

·

If the cut surface of the old adhesive is left exposed for a long time, the adhesion strength will be reduced, so apply the new adhesive quickly.



a.
B565174C01
1.667,1.104 1.417,1.104 1.417,1.104 1.417,1.771 true 1.417,1.406 1.667,1.406 true 1.354,1.813 1.667,1.969 0.313,0.156 10 false *a
*a Matchmark


Position the back door glass.

i.

Using suction cups, place a new back door glass in the correct position.


ii.

Check that the whole contact surface of the back door glass rim is perfectly even.


iii.

Align the matchmarks on the back door glass and back door panel.

NOTICE:

Check that the back window glass clips are engaged to the back door panel correctly.



iv.

Remove the back door glass.



b.

Using a brush, coat the installation surfaces on the back door panel with body primer.

NOTICE:
·

Do not coat the adhesive with body primer.

·

Do not apply too much body primer.

·

Allow the body primer to dry for 3 minutes or more.

·

Throw away any leftover body primer.



HINT:

If an area other than specified is coated by accident, wipe off the body primer with a clean piece of cloth before it dries.



c.

Using a brush or sponge, coat the adhesive application area with glass primer.

B565187C01
3.823,2.438 3.615,2.021 false 6.156,1.375 6.042,1.729 6.042,1.729 5.635,1.385 false 0.219,0.167 0.604,0.458 0.385,0.292 12 false *A 2.427,0.927 2.583,1.125 0.156,0.198 10 false A 2.448,1.219 2.604,1.417 0.156,0.198 10 false A 0.729,1.25 0.906,1.458 0.177,0.208 10 false B 0.25,1.167 0.427,1.375 0.177,0.208 10 false B 0.25,1.552 0.427,1.76 0.177,0.208 10 false C 0.688,1.552 0.865,1.76 0.177,0.208 10 false C 2.313,1.885 2.521,2.063 0.208,0.177 10 true D 2.333,2.427 2.542,2.604 0.208,0.177 10 true D 1.948,3.135 2.344,3.365 0.396,0.229 10 false A-A 4.927,0.375 5.323,0.604 0.396,0.229 10 false B-B 4.906,1.771 5.302,2 0.396,0.229 10 false C-C 4.927,3.25 5.323,3.479 0.396,0.229 10 false D-D 2.604,3.427 2.76,3.625 0.156,0.198 10 false a 5.615,0.594 5.896,0.802 0.281,0.208 10 false b 6.115,0.594 6.323,0.792 0.208,0.198 10 false b 5.708,2.042 5.917,2.24 0.208,0.198 10 false c 5.542,3.656 5.75,3.854 0.208,0.198 10 false d 3.833,2.438 4.146,2.635 0.313,0.198 10 false *a 5.99,1.76 6.302,1.958 0.313,0.198 10 false *b
*A Back Side - -
*a Adhesive Positioning Center *b Ceramic Notch
V100155

Glass Primer - -


Standard Dimension:
Area Dimension Area Dimension
a 25.1 mm (0.988 in.) b 19.4 mm (0.764 in.)
c 29.2 mm (1.15 in.) d 18.1 mm (0.713 in.)


NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:
·

Apply glass primer to the ceramic notches.

·

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.




d.

Apply adhesive to the back door.

Adhesive:

Toyota Genuine Windshield Glass Adhesive (High modulus type) or equivalent


i.
B214800C28
1.198,0.438 1.385,0.5 false 0.5,0.625 0.656,0.823 0.156,0.198 10 false a 1.344,1.365 1.5,1.563 0.156,0.198 10 false a 1.115,0.885 1.271,1.083 0.156,0.198 10 false b 0.76,1 0.917,1.198 0.156,0.198 10 false b 1.406,0.438 1.646,0.615 0.24,0.177 10 false *a
*a Nozzle


Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Dimension
a 12.0 to 15.0 mm (0.472 to 0.591 in.)
b 8.0 to 11.0 mm (0.315 to 0.433 in.)



ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the back door as shown in the illustration.

B565188C01
2.896,3.552 3.021,3.677 false 5.125,3.521 5.49,3.552 false 5.052,1.969 5.479,1.969 5.479,1.969 5.479,2.156 false 5.271,2.156 5.271,1.969 false 5.042,0.375 5.708,0.375 5.708,0.375 5.708,0.563 false 5.302,0.563 5.302,0.375 false 2.156,3.896 1.802,3.958 false 3.167,3.979 2.76,3.896 false 4.802,3.938 5.042,3.885 false 5.469,3.885 5.708,3.99 false 4.927,2.729 5.177,2.542 false 6.104,2.698 5.844,2.542 false 6.604,1.135 6.344,0.979 false 0.208,0.135 0.583,0.375 0.375,0.24 12 false *A 3.052,3.604 3.365,3.802 0.313,0.198 10 false *a 4.875,3.417 5.188,3.615 0.313,0.198 10 false *a 4.865,1.885 5.177,2.083 0.313,0.198 10 false *a 4.854,0.292 5.167,0.49 0.313,0.198 10 false *a 1.948,1.052 2.104,1.25 0.156,0.198 10 false A 1.948,1.313 2.104,1.51 0.156,0.198 10 false A 1.75,3.365 2.208,3.563 0.458,0.198 10 false A-A 3.635,1.354 3.802,1.563 0.167,0.208 10 false B 4.01,1.26 4.177,1.469 0.167,0.208 10 false B 3.677,1.635 3.844,1.844 0.167,0.208 10 false C 4.083,1.615 4.25,1.823 0.167,0.208 10 false C 1.938,1.771 2.104,1.979 0.167,0.208 10 false D 1.927,2.052 2.094,2.26 0.167,0.208 10 true D 4.438,0.115 4.896,0.313 0.458,0.198 10 false B-B 4.5,1.563 4.958,1.76 0.458,0.198 10 false C-C 4.604,3.177 5.063,3.375 0.458,0.198 10 false D-D 2.625,4.229 2.802,4.438 0.177,0.208 10 false a 2.417,4.458 2.688,4.677 0.271,0.219 10 false b 5.49,1.375 5.667,1.583 0.177,0.208 10 false c 5.51,1.667 5.688,1.875 0.177,0.208 10 false d 6.083,1.333 6.26,1.542 0.177,0.208 10 false e 6.104,1.552 6.281,1.76 0.177,0.208 10 false f 5.25,2.854 5.427,3.063 0.177,0.208 10 false g 5.688,2.885 5.865,3.094 0.177,0.208 10 false h 5.5,3.094 5.677,3.302 0.177,0.208 10 false i 5.344,4.229 5.521,4.438 0.177,0.208 10 false j 5.219,4.469 5.396,4.677 0.177,0.208 10 false k 1.594,3.906 1.906,4.104 0.313,0.198 10 false *b 3.208,3.917 3.521,4.115 0.313,0.198 10 false *b 4.625,3.885 4.938,4.083 0.313,0.198 10 false *b 5.75,3.917 6.063,4.115 0.313,0.198 10 false *b 4.75,2.698 5.063,2.896 0.313,0.198 10 false *b 6.156,2.635 6.469,2.833 0.313,0.198 10 false *b 6.656,1.094 6.969,1.292 0.313,0.198 10 false *b
*A Back Side - -
*a Adhesive Positioning Center *b Scribed Line
V100155

Adhesive - -


Standard Dimension:
Area Dimension Area Dimension
a 7.5 mm (0.295 in.) b 25.1 mm (0.988 in.)
c 4.5 mm (0.177 in.) d 11.4 mm (0.449 in.)
e 16.6 mm (0.654 in.) f 20.6 mm (0.811 in.)
g 10.6 mm (0.417 in.) h 10.6 mm (0.417 in.)
i 29.2 mm (1.15 in.) j 7.5 mm (0.295 in.)
k 18.1 mm (0.713 in.) - -




e.

Install the back door glass.

i.
B565174C01
1.667,1.104 1.417,1.104 1.417,1.104 1.417,1.771 true 1.417,1.406 1.667,1.406 true 1.354,1.813 1.667,1.969 0.313,0.156 10 false *a
*a Matchmark


Using suction cups, position the back door glass so that the matchmarks are aligned, and press it in gently along the rim.

NOTICE:
·

Check that the 3 back window glass spacers are engaged to the back door panel correctly.

·

Check the clearance between the back door panel and back door glass.




ii.

Lightly press the front surface of the back door glass to ensure a close fit.

HINT:

Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.



iii.

Using a scraper, remove any excess or protruding adhesive.


iv.

Hold the back door glass using protective tape until the applied adhesive becomes hard.

HINT:

Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.




f.

Connect each connector.


Hide 7.INSPECT FOR LEAK

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 85110R 8.INSTALL REAR WIPER MOTOR ASSEMBLY