Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM37A0E _58 Vehicle Interior _086889 METER / GAUGE / DISPLAY _0416706 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Engine Oil Level Sensor Circuit  


DESCRIPTION

The combination meter assembly and engine oil level sensor are connected via direct line. The combination meter assembly determines the engine oil level based on the engine oil level sensor status signal.

HINT:

As the engine oil level may be unstable when the engine is cold or running at high speeds, the combination meter assembly receives the engine coolant temperature signal and engine speed signal from the ECM via CAN communication in order to prevent the oil level warnings from being output erroneously.


WIRING DIAGRAM

E436072E01
0.531,4.448 4.198,4.646 3.667,0.198 10 false : CAN Communication Line 1.021,3.896 1.479,4.094 0.458,0.198 10 false C34 1.021,2.688 4.542,2.885 3.521,0.198 10 false Engine Oil Level Sensor 1.021,4.052 4.542,4.25 3.521,0.198 10 false Engine Oil Level Sensor 1.01,2.531 1.469,2.729 0.458,0.198 10 false C34 2,1.906 2.458,2.104 0.458,0.198 10 false LVL 1.969,3.271 2.427,3.469 0.458,0.198 10 false LOIL 1.531,1.198 1.99,1.396 0.458,0.198 10 false ECM 5.635,1.573 6.25,1.771 0.615,0.198 10 false 12 V 4.698,2.688 5.156,2.885 0.458,0.198 10 false H21 4.698,2.865 6.677,3.188 1.979,0.323 10 false Combination Meter Assembly 4.958,1.906 5.573,2.104 0.615,0.198 10 false OILW 2.99,1.917 3.302,2.115 0.313,0.198 10 false *1 3.385,2.75 3.698,2.948 0.313,0.198 10 false *2 4.385,3.74 6.833,3.938 2.448,0.198 10 false *1: for HV Model 4.385,4.146 6.833,4.344 2.448,0.198 10 false *2: for Gasoline Model 2.375,1.906 2.531,2.104 0.156,0.198 10 false 1 2.375,3.271 2.531,3.469 0.156,0.198 10 false 1 4.677,1.906 4.99,2.104 0.313,0.198 10 false 27

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

The following troubleshooting procedure is based on the assumption that the SFI system is normal. Confirm that the SFI system is not malfunctioning before performing the following procedure.

for HV Model: Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

for Gasoline Model: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.INSPECT ENGINE OIL LEVEL SENSOR


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ENGINE OIL LEVEL SENSOR - COMBINATION METER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (ENGINE OIL LEVEL SENSOR - COMBINATION METER ASSEMBLY)
a.

Disconnect the H21 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for HV Model):
Tester Connection Condition Specified Condition
C34-1 (LVL) - H21-27 (OILW) Always Below 1 Ω
C34-1 (LVL) or H21-27 (OILW) - Body ground Always 10 kΩ or higher


Standard Resistance (for Gasoline Model):
Tester Connection Condition Specified Condition
C34-1 (LOIL) - H21-27 (OILW) Always Below 1 Ω
C34-1 (LOIL) or H21-27 (OILW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR