Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM37A0E _58 Vehicle Interior _086889 METER / GAUGE / DISPLAY _0416706 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Odo/Trip Switch Malfunction  


DESCRIPTION

The trip switch is connected to the combination meter assembly via direct line. When the ODO/TRIP switch is operated, the display of the multi-information display changes or the displayed value is reset.

WIRING DIAGRAM

E369056E13
1.854,2.688 2.563,2.885 0.708,0.198 10 false Trip Switch 1.854,2.531 2.219,2.729 0.365,0.198 10 false H23 1.927,1.115 2.604,1.469 0.677,0.354 10 false ODO/TRIP Switch 4.521,3.167 6.365,3.365 1.844,0.198 10 false Combination Meter Assembly 4.531,2.99 4.896,3.188 0.365,0.198 10 false H22 4.646,2.042 5.01,2.24 0.365,0.198 10 false SW3 4.656,0.844 5.021,1.042 0.365,0.198 10 false ODO 2.677,0.854 2.948,1.031 0.271,0.177 10 false A/B 2.792,2.042 2.948,2.229 0.156,0.188 10 false E 3.01,2.042 3.167,2.229 0.156,0.188 10 false 1 4.448,2.042 4.802,2.26 0.354,0.219 10 false 5 4.438,0.844 4.594,1.031 0.156,0.188 10 false 1 3.021,0.854 3.177,1.042 0.156,0.188 10 false 3 5.719,0.5 5.99,0.719 0.271,0.219 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ODO/TRIP Change Switch ODO/TRIP switch OFF or ON OFF: Switch released
ON: Switch pushed
When the switch is built into the combination meter assembly or is connected via direct line, the input value is displayed.
Body Electrical > Combination Meter > Data List
Tester Display
ODO/TRIP Change Switch
50003 409 2
OK:

ODO/TRIP switch condition displayed on the GTS changes with the actual switch operation.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.INSPECT TRIP SWITCH
2.INSPECT TRIP SWITCH


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRIP SWITCH - COMBINATION METER ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (TRIP SWITCH - COMBINATION METER ASSEMBLY)
a.

Disconnect the H22 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H23-3 (A/B) - H22-1 (ODO) Always Below 1 Ω
H23-1 (E) - H22-5 (SW3) Always Below 1 Ω
H23-3 (A/B) or H22-1 (ODO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR