This DTC is stored when the combination meter assembly detects an open in a front turn signal light circuit or rear turn signal light circuit.
If there is an open in a front turn signal light circuit or rear turn signal light circuit, the turn signal lights on the side with the open circuit will blink faster than usual.
If there is an open in a side turn signal light circuit, DTC B150718 will not be stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B150718 | Turn Signal Light Circuit Current Below Threshold | Diagnosis Condition:
Auxiliary battery voltage is 10 V or more Malfunction Status: ·
Open in front turn signal light circuit ·
Open in rear turn signal light circuit |
·
Headlight assembly -
Front turn signal light socket -
Front turn signal light bulb ·
Rear combination light assembly -
Rear combination light cord -
Rear turn signal light socket -
Rear turn signal light bulb ·
Harness or connector ·
Combination meter assembly |
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Inspect the turn signal light bulbs before performing the following procedure.
Check the problem symptoms.
| Result | Proceed to |
|---|---|
| LH side front turn signal light does not blink | A |
| LH side rear turn signal light does not blink | B |
| RH side front turn signal light does not blink | C |
| RH side rear turn signal light does not blink | D |
A
B
C
D
Interchange the front turn signal light socket LH with RH and connect the connectors.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY
Operate the turn signal switch and check that the LH side front turn signal light operates normally.
If the LH side front turn signal light operates normally, the front turn signal light socket LH is malfunctioning.
| Result | Proceed to |
|---|---|
| LH side front turn signal light operates normally | A |
| Problem symptoms do not change
(LH side front turn signal light does not blink) |
B |
A
B
Disconnect the A64 headlight assembly LH connector.
Disconnect the H22 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A64-1 (B) - H22-11 (LL) | Always | Below 1 Ω |
| A64-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Interchange the rear turn signal light socket LH with RH and connect the connectors.
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY
Operate the turn signal switch and check that the LH side rear turn signal light operates normally.
If the LH side rear turn signal light operates normally, the rear turn signal light socket LH is malfunctioning.
| Result | Proceed to |
|---|---|
| LH side rear turn signal light operates normally | A |
| Problem symptoms do not change
(LH side rear turn signal light does not blink) |
B |
A
B
Interchange the rear combination light cord LH with RH and connect the connectors.
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>REMOVAL
Operate the turn signal switch and check that the LH side rear turn signal light operates normally.
If the LH side rear turn signal light operates normally, the rear combination light cord LH is malfunctioning.
| Result | Proceed to |
|---|---|
| LH side rear turn signal light operates normally | A |
| Problem symptoms do not change
(LH side rear turn signal light does not blink) |
B |
A
B
Disconnect the M59 rear combination light assembly LH connector.
Disconnect the H22 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M59-1 (TRN) - H22-10 (TRNL) | Always | Below 1 Ω |
| M59-3 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Interchange the front turn signal light socket RH with LH and connect the connectors.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY
Operate the turn signal switch and check that the RH side front turn signal light operates normally.
If the RH side front turn signal light operates normally, the front turn signal light socket RH is malfunctioning.
| Result | Proceed to |
|---|---|
| RH side front turn signal light operates normally | A |
| Problem symptoms do not change
(RH side front turn signal light does not blink) |
B |
A
B
Disconnect the A63 headlight assembly RH connector.
Disconnect the H22 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A63-1 (B) - H22-7 (LR) | Always | Below 1 Ω |
| A63-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Interchange the rear turn signal light socket RH with LH and connect the connectors.
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY
Operate the turn signal switch and check that the RH side rear turn signal light operates normally.
If the RH side rear turn signal light operates normally, the rear turn signal light socket RH is malfunctioning.
| Result | Proceed to |
|---|---|
| RH side rear turn signal light operates normally | A |
| Problem symptoms do not change
(RH side rear turn signal light does not blink) |
B |
A
B
Interchange the rear combination light cord RH with LH and connect the connectors.
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>REMOVAL
Operate the turn signal switch and check that the RH side rear turn signal light operates normally.
If the RH side rear turn signal light operates normally, the rear combination light cord RH is malfunctioning.
| Result | Proceed to |
|---|---|
| RH side rear turn signal light operates normally | A |
| Problem symptoms do not change
(RH side rear turn signal light does not blink) |
B |
A
B
Disconnect the M8 rear combination light assembly RH connector.
Disconnect the H22 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M8-1 (TRN) - H22-13 (TRNR) | Always | Below 1 Ω |
| M8-3 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG