Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › 2020.02–2020.11
RM37A0E _57 Power Source / Network _086883 NETWORKING _0417284 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Blind Spot Monitor Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Blind Spot Monitor Sensor Communication Stop Mode Communication stop for "Blind Spot Monitor Master" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Blind spot monitor sensor LH branch line or connector

·

Power source circuit of blind spot monitor sensor LH

·

Blind spot monitor sensor LH ground circuit

·

Blind spot monitor sensor LH



WIRING DIAGRAM

C424579E01
0.083,1.823 0.542,2.021 0.458,0.198 10 false M97 0.438,1.823 4.719,2.115 4.281,0.292 10 false No. 10 Global CAN Junction Connector 1.656,0.771 1.813,0.969 0.156,0.198 10 false 3 1.667,1.354 1.969,1.573 0.302,0.219 10 false 9 1.635,2.354 4.698,2.667 3.063,0.313 10 false from IG1-NO. 1 Relay 5.583,0.875 6.198,1.073 0.615,0.198 10 false CA1P 5.583,1.469 6.198,1.667 0.615,0.198 10 false CA1N 5.583,2.365 6.198,2.563 0.615,0.198 10 false BLB 5.583,3.198 6.198,3.396 0.615,0.198 10 false BLGD 4.771,4.042 5.229,4.24 0.458,0.198 10 false M43 5.135,4.042 7.104,4.406 1.969,0.365 10 false Blind Spot Monitor Sensor LH 3.646,2.24 6.708,2.438 3.063,0.198 10 false ECU-IG1 NO. 3 5.385,0.771 5.542,0.969 0.156,0.198 10 false 2 5.385,1.354 5.542,1.552 0.156,0.198 10 false 7 5.385,2.292 5.542,2.49 0.156,0.198 10 false 5 5.333,3.135 5.635,3.354 0.302,0.219 10 false 10

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (BLIND SPOT MONITOR SENSOR LH BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the M43 blind spot monitor sensor LH connector.


c.
C400475C16
1.49,0.74 1.865,0.969 0.375,0.229 1.375,1.177 1.542,1.177 1.542,1.177 1.542,1.927 true 1.375,2.917 1.542,2.917 1.542,2.917 1.542,2.167 true 0.167,0.135 0.479,0.292 0.313,0.156 10 false *a 1.552,0.771 1.865,0.969 0.313,0.198 10 false M43 0.979,1.094 1.594,1.292 0.615,0.198 10 false CA1P 0.979,2.833 1.594,3.031 0.615,0.198 10 false CA1N
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M43-2 (CA1P) - M43-7 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C400475C21
1.49,0.74 1.865,0.969 0.375,0.229 2.24,2.917 2.052,2.917 2.052,2.917 2.052,2.167 true 0.167,0.135 0.479,0.292 0.313,0.156 10 false *a 1.552,0.771 1.865,0.969 0.313,0.198 10 false M43 2.292,2.823 2.906,3.021 0.615,0.198 10 false BLGD
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M43-10 (BLGD) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.
C400475C20
1.5,0.583 1.875,0.813 0.375,0.229 2.292,1.094 2.042,1.094 2.042,1.094 2.042,1.927 true 0.167,0.135 0.479,0.292 0.313,0.156 10 false *a 1.563,0.604 1.875,0.802 0.313,0.198 10 false M43 2.385,1.021 3,1.219 0.615,0.198 10 false BLB
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M43-5 (BLB) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)