Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › 2020.02–2020.11
RM37A0E _57 Power Source / Network _086883 NETWORKING _0417284 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Millimeter Wave Radar Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Millimeter Wave Radar Sensor Communication Stop Mode Communication stop for "Front Radar" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Millimeter wave radar sensor assembly branch line or connector

·

Power source circuit of millimeter wave radar sensor assembly

·

Millimeter wave radar sensor assembly ground circuit

·

Millimeter wave radar sensor assembly



WIRING DIAGRAM

C424579E02
5.521,4.042 6.917,4.573 1.396,0.531 10 false Millimeter Wave Radar Sensor Assembly 5.219,4.042 5.708,4.302 0.49,0.26 10 false B6 0.5,1.813 3.125,2.281 2.625,0.469 10 false No. 5 Global CAN Junction Connector 0.167,1.813 0.708,2.115 0.542,0.302 10 false H93 1.688,0.76 2.229,1.063 0.542,0.302 10 false 2 1.688,1.344 2.229,1.646 0.542,0.302 10 false 8 5.354,0.74 5.896,1.042 0.542,0.302 10 false 3 5.354,1.354 5.896,1.656 0.542,0.302 10 false 2 5.365,2.271 5.906,2.573 0.542,0.302 10 false 8 5.365,3.115 5.906,3.417 0.542,0.302 10 false 1 5.615,0.854 6.156,1.156 0.542,0.302 10 false CA2H 5.604,1.427 6.146,1.729 0.542,0.302 10 false CA2L 5.604,2.375 6.146,2.677 0.542,0.302 10 false IGB 5.604,3.24 6.146,3.542 0.542,0.302 10 false SGND 3.708,2.26 4.844,2.542 1.135,0.281 10 false ECU-IG1 NO. 3 1.635,2.354 3.427,2.792 1.792,0.438 10 false from IG1-NO. 1 Relay

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the B6 millimeter wave radar sensor assembly connector.


c.
C424521C01
0.333,1.052 0.698,1.26 0.365,0.208 1.427,0.229 1.594,0.229 1.594,0.229 1.594,1.063 true 1.948,0.229 1.781,0.229 1.781,0.229 1.781,1.063 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 0.427,1.073 0.823,1.292 0.396,0.219 10 false B6 2.042,0.146 2.5,0.479 0.458,0.333 10 false CA2H 1.042,0.156 1.417,0.406 0.375,0.25 10 false CA2L
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B6-3 (CA2H) - B6-2 (CA2L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C424521C02
0.333,1.052 0.698,1.26 0.365,0.208 1.26,0.229 1.427,0.229 1.427,0.229 1.427,1.063 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 0.406,1.073 0.802,1.292 0.396,0.219 10 false B6 0.792,0.156 1.281,0.427 0.49,0.271 10 false SGND
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B6-1 (SGND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.
C424521C03
0.333,1.052 0.698,1.26 0.365,0.208 2.135,1.958 1.969,1.958 1.969,1.958 1.969,1.375 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 0.406,1.073 0.802,1.292 0.396,0.219 10 false B6 2.219,1.875 2.594,2.063 0.375,0.188 10 false IGB
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B6-8 (IGB) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)