Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model)
RM37A0E _57 Power Source / Network _086883 NETWORKING _0417284 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Tire Pressure Monitor ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Tire Pressure Monitor ECU Communication Stop Mode Communication stop for "Tire Pressure" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Tire pressure warning ECU and receiver branch line or connector

·

Power source circuit of tire pressure warning ECU and receiver

·

Tire pressure warning ECU and receiver ground circuit

·

Tire pressure warning ECU and receiver



WIRING DIAGRAM

C424580E03
5.583,4.771 6.969,5.344 1.385,0.573 10 false Tire Pressure Warning ECU and Receiver 5.219,4.771 5.729,5.135 0.51,0.365 10 false M51 0.521,1.938 3,2.281 2.479,0.344 10 false No. 2 Global CAN Junction Connector 0.198,1.927 0.688,2.188 0.49,0.26 10 false H90 1.729,0.854 2.219,1.115 0.49,0.26 10 false 9 1.698,1.448 2.188,1.708 0.49,0.26 10 false 19 5.667,0.979 6.208,1.24 0.542,0.26 10 false CANH 5.656,1.552 6.198,1.813 0.542,0.26 10 false CANL 5.417,0.865 5.906,1.125 0.49,0.26 10 false 9 5.365,1.448 5.854,1.708 0.49,0.26 10 false 10 5.438,2.333 5.927,2.594 0.49,0.26 10 false 1 5.448,3.167 5.938,3.427 0.49,0.26 10 false 7 5.385,4.01 5.875,4.271 0.49,0.26 10 false 12 5.646,2.51 6.188,2.771 0.542,0.26 10 false IG 5.656,3.281 6.198,3.542 0.542,0.26 10 false +B 5.646,4.125 6.188,4.385 0.542,0.26 10 false GND 3.854,2.344 4.979,2.573 1.125,0.229 10 false ECU-IG1 NO. 3 3.865,3.156 4.99,3.385 1.125,0.229 10 false ECU-B NO. 2 2.26,3.25 3.917,3.51 1.656,0.26 10 false from Battery 1.698,2.427 3.354,2.688 1.656,0.26 10 false from IG1-NO. 1 Relay

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (TIRE PRESSURE WARNING ECU AND RECEIVER BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the M51 tire pressure warning ECU and receiver connector.


c.
C424509C01
0.323,0.938 0.771,1.219 0.448,0.281 2.219,1.865 1.781,1.865 1.781,1.865 1.781,1.365 true 1.198,1.865 1.615,1.865 1.615,1.865 1.615,1.365 true 0.094,0.083 0.458,0.344 0.365,0.26 10 false *a 0.417,0.969 0.781,1.229 0.365,0.26 10 false M51 0.74,1.771 1.25,2.052 0.51,0.281 10 false CANH 2.292,1.75 2.802,2.031 0.51,0.281 10 false CANL
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M51-9 (CANH) - M51-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C424509C02
0.323,0.938 0.771,1.219 0.448,0.281 2.365,1.854 2.104,1.854 2.104,1.854 2.104,1.354 true 0.094,0.083 0.458,0.344 0.365,0.26 10 false *a 0.417,0.969 0.781,1.229 0.365,0.26 10 false M51 2.417,1.74 2.927,2.021 0.51,0.281 10 false GND
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M51-12 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.
C424509C03
0.323,0.938 0.771,1.219 0.448,0.281 1.115,1.875 1.292,1.875 1.292,1.875 1.292,1.375 true 1.083,0.281 1.302,0.281 1.302,0.281 1.302,1.01 true 0.094,0.083 0.458,0.344 0.365,0.26 10 false *a 0.417,0.969 0.781,1.229 0.365,0.26 10 false M51 0.875,0.188 1.271,0.521 0.396,0.333 10 false IG 0.875,1.781 1.385,2.063 0.51,0.281 10 false +B
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M51-1 (IG) - Body ground Ignition switch ON 10 to 16 V
M51-7 (+B) - Body ground Always 10 to 16 V



Result:
Result
OK
NG



OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)