Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › 2020.02–2020.11
RM37A0E _57 Power Source / Network _086883 NETWORKING _0417284 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Clearance Warning ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Clearance Warning ECU Communication Stop Mode Communication stop for "Clearance Warning (Clearance Sonar)" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Clearance warning ECU assembly branch line or connector

·

Power source circuit of clearance warning ECU assembly

·

Clearance warning ECU assembly ground circuit

·

Clearance warning ECU assembly



WIRING DIAGRAM

C424574E01
5.51,5.073 7.021,5.667 1.51,0.594 10 false Clearance Warning ECU Assembly 5.115,5.083 5.5,5.479 0.385,0.396 10 false H46 0.229,1.948 0.615,2.344 0.385,0.396 10 false H93 0.563,1.938 3.063,2.302 2.5,0.365 10 false No. 5 Global CAN Junction Connector 5.719,0.958 6.063,1.292 0.344,0.333 10 false R1 5.729,1.479 6.073,1.813 0.344,0.333 10 false R2 5.719,2.427 6.063,2.76 0.344,0.333 10 false IG 5.74,4.146 6.083,4.479 0.344,0.333 10 false E 1.76,2.406 3.552,2.823 1.792,0.417 10 false from IG1-NO. 1 Relay 1.646,0.813 1.802,1.01 0.156,0.198 10 false 5 1.625,1.313 1.896,1.521 0.271,0.208 10 false 11 5.323,0.781 5.667,0.979 0.344,0.198 10 false 17 5.323,1.323 5.646,1.5 0.323,0.177 10 false 18 5.375,2.302 5.615,2.49 0.24,0.188 10 false 1 5.354,3.979 5.75,4.229 0.396,0.25 10 false 28 3.958,2.26 5.75,2.677 1.792,0.417 10 false ECU-IG1 NO. 4

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (CLEARANCE WARNING ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the H46 clearance warning ECU assembly connector.


c.
C380493C71
1.521,0.135 1.896,0.396 0.375,0.26 2.948,1.167 2.958,0.604 2.958,0.604 2.615,0.604 true 2.823,1.198 2.823,1.896 2.823,1.896 2.573,1.896 true 1.594,0.188 2.052,0.385 0.458,0.198 10 false H46 2.354,1.792 2.813,1.99 0.458,0.198 10 false R1 2.396,0.51 2.854,0.708 0.458,0.198 10 false R2 0.135,0.094 0.594,0.292 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H46-17 (R1) - H46-18 (R2) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C380493C67
1.521,0.135 1.896,0.396 0.375,0.26 1.573,1.333 1.573,1.917 1.573,1.917 1.323,1.917 true 1.594,0.188 2.052,0.385 0.458,0.198 10 false H46 1.188,1.833 1.646,2.031 0.458,0.198 10 false E 0.135,0.094 0.594,0.292 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H46-28 (E) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.
C380493C68
1.521,0.135 1.896,0.396 0.375,0.26 0.479,1.188 0.49,1.917 0.49,1.917 0.719,1.917 true 1.594,0.188 2.052,0.385 0.458,0.198 10 false H46 0.771,1.844 1.229,2.042 0.458,0.198 10 false IG 0.135,0.094 0.594,0.292 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H46-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)