Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model)
RM37A0E _57 Power Source / Network _086883 NETWORKING _0417284 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  DCM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
DCM Communication Stop Mode Communication stop for "DCM" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Telematics transceiver branch line or connector

·

Power source circuit of telematics transceiver

·

Telematics transceiver ground circuit

·

Telematics transceiver



WIRING DIAGRAM

C382030E42
0.219,1.938 0.677,2.135 0.458,0.198 10 false H95 0.594,1.938 2.958,2.313 2.365,0.375 10 false No. 6 Global CAN Junction Connector 1.698,1.396 2.156,1.594 0.458,0.198 10 false 16 1.74,0.833 2.198,1.031 0.458,0.198 10 false 5 5.406,0.833 5.844,1.063 0.438,0.229 10 false 15 5.406,1.385 5.844,1.615 0.438,0.229 10 false 16 5.677,0.948 6.219,1.188 0.542,0.24 10 false CANP 5.667,1.51 6.208,1.75 0.542,0.24 10 false CANN 5.667,4.094 6.208,4.333 0.542,0.24 10 false E 5.396,3.969 5.938,4.208 0.542,0.24 10 false 4 5.063,4.865 5.604,5.104 0.542,0.24 10 false H10 5.438,4.854 7.031,5.281 1.594,0.427 10 false Telematics Transceiver 5.667,3.49 6.208,3.729 0.542,0.24 10 false IG2 5.667,2.906 6.208,3.146 0.542,0.24 10 false ACC 5.667,2.313 6.208,2.552 0.542,0.24 10 false +B 4.125,2.156 5.177,2.479 1.052,0.323 10 false DCM 3.854,3.333 5.271,3.656 1.417,0.323 10 false ECU-IG2 NO. 3 3.99,2.75 5.406,3.073 1.417,0.323 10 false ECU-ACC 1.625,3.458 3.25,3.969 1.625,0.51 10 false from IG2-NO. 2 Relay 5.396,3.375 5.938,3.615 0.542,0.24 10 false 7 5.396,2.781 5.938,3.021 0.542,0.24 10 false 8 5.385,2.208 5.927,2.448 0.542,0.24 10 false 1 2.208,2.281 3.625,2.594 1.417,0.313 10 false from Battery 1.958,2.875 3.583,3.385 1.625,0.51 10 false from ACC Relay

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (TELEMATICS TRANSCEIVER BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the H10 telematics transceiver connector.


c.
C361493C76
1.469,0.365 1.906,0.625 0.438,0.26 2,1.875 2,0.865 2,0.865 2.156,0.865 true 1.854,1.875 1.854,0.865 1.854,0.865 1.708,0.865 true 1.563,0.406 2.021,0.604 0.458,0.198 10 false H10 2.26,0.792 2.958,1.063 0.698,0.271 10 false CANN 1.26,0.792 1.958,1.063 0.698,0.271 10 false CANP 0.125,0.063 0.583,0.26 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Telematics Transceiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H10-15 (CANP) - H10-16 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (TELEMATICS TRANSCEIVER)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C361493C77
1.458,0.354 1.896,0.604 0.438,0.25 0.406,1.865 0.396,0.594 0.396,0.594 0.552,0.594 true 0.531,1.635 0.531,0.854 0.531,0.854 0.677,0.854 true 2.375,1.635 2.375,0.854 2.375,0.854 2.521,0.854 true 0.552,1.938 0.552,2.76 0.552,2.76 0.698,2.76 true 1.563,0.396 2.021,0.594 0.458,0.198 10 false H10 0.656,0.51 1.354,0.781 0.698,0.271 10 false IG2 0.76,0.771 1.104,1.094 0.344,0.323 10 false +B 0.115,0.083 0.813,0.354 0.698,0.271 10 false *a 2.615,0.781 2.958,1.104 0.344,0.323 10 false E 0.792,2.677 1.26,3 0.469,0.323 10 false ACC
*a Front view of wire harness connector
(to Telematics Transceiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H10-4 (E) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H10-1 (+B) - Body ground Always 11 to 14 V
H10-7 (IG2) - Body ground Ignition switch ON 11 to 14 V
H10-8 (ACC) - Body ground Ignition switch ACC 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)