| Symptom | Trouble Area |
|---|---|
| There are ECUs or sensors that display a communication stop on the bus diagnostic screen. Or, there are ECUs or sensors that display communication stop history on the "Detail" screen. | ·
CAN main bus line, CAN branch line or connector ·
Central gateway ECU (network gateway ECU) ·
Outer mirror control ECU assembly LH (w/ Seat Position Memory System) ·
Outer mirror control ECU assembly RH (w/ Seat Position Memory System) ·
Position control ECU assembly LH (w/ Seat Position Memory System) ·
Air conditioning amplifier assembly ·
Main body ECU (multiplex network body ECU) ·
Meter mirror sub-assembly (w/ Headup Display System) ·
Certification ECU (smart key ECU assembly) ·
Combination meter assembly ·
Multiplex network door ECU ·
No. 3 global CAN junction connector ·
No. 4 global CAN junction connector ·
No. 9 global CAN junction connector |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM
Before replacing the main body ECU (multiplex network body ECU) or certification ECU (smart key ECU assembly), refer to Service Bulletin.
The battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing troubleshooting, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Disconnect the cable from the negative (-) battery terminal.
| *a | Component with harness connected
(Central Gateway ECU (Network Gateway ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H59-15 (CA5H) - H59-16 (CA5L) | Cable disconnected from negative (-) battery terminal | Below 70 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Central Gateway ECU (Network Gateway ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H59-15 (CA5H) - H59-16 (CA5L) | Cable disconnected from negative (-) battery terminal | 54 Ω or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Component with harness connected
(Central Gateway ECU (Network Gateway ECU)) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H59-15 (CA5H) - H56-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H59-16 (CA5L) - H56-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Component with harness connected
(Central Gateway ECU (Network Gateway ECU)) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H59-15 (CA5H) - H56-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H59-16 (CA5L) - H56-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H91 No. 3 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to No. 4 Global CAN Junction Connector |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-6 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H91-16 (CANL) - H56-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-2 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H91-12 (CANL) - H56-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to Certification ECU (Smart Key ECU Assembly) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-3 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H91-13 (CANL) - H56-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to Air Conditioning Amplifier Assembly |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-4 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H91-14 (CANL) - H56-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| w/ Seat Position Memory System | A |
| w/o Seat Position Memory System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to Outer Mirror Control ECU Assembly RH |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-5 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H91-15 (CANL) - H56-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H59 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-2 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H91-12 (CANL) - H56-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H48 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to Certification ECU (Smart Key ECU Assembly) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-3 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H91-13 (CANL) - H56-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H62 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to Air Conditioning Amplifier Assembly |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-4 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H91-14 (CANL) - H56-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the J7 outer mirror control ECU assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to Outer Mirror Control ECU Assembly RH |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-5 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H91-15 (CANL) - H56-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H92 No. 4 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to No. 9 Global CAN Junction Connector |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-4 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H92-10 (CANL) - H56-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to No. 3 Global CAN Junction Connector |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-3 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H92-9 (CANL) - H56-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to Main Body ECU (Multiplex Network Body ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-1 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H92-7 (CANL) - H56-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| w/ Headup Display System | A |
| w/o Headup Display System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to Meter Mirror Sub-assembly |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-2 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H92-8 (CANL) - H56-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| w/ Seat Position Memory System | A |
| w/o Seat Position Memory System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to Outer Mirror Control ECU Assembly LH |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-5 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H92-11 (CANL) - H56-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H43 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to Main Body ECU (Multiplex Network Body ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-1 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H92-7 (CANL) - H56-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H31 meter mirror sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to Meter Mirror Sub-assembly |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-2 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H92-8 (CANL) - H56-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the J23 outer mirror control ECU assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to Outer Mirror Control ECU Assembly LH |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-5 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| H92-11 (CANL) - H56-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the M96 No. 9 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
*b | to No. 4 Global CAN Junction Connector |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M96-3 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M96-9 (CANL) - H56-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
*b | to Combination Meter Assembly |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M96-4 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M96-10 (CANL) - H56-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
*b | to Multiplex Network Door ECU |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M96-1 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M96-7 (CANL) - H56-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| w/ Seat Position Memory System | A |
| w/o Seat Position Memory System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
*b | to Position Control ECU Assembly LH |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M96-2 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M96-8 (CANL) - H56-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H21 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
*b | to Combination Meter Assembly |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M96-4 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M96-10 (CANL) - H56-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the W18 multiplex network door ECU connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
*b | to Multiplex Network Door ECU |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M96-1 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M96-7 (CANL) - H56-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the e25 position control ECU assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
*b | to Position Control ECU Assembly LH |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M96-2 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M96-8 (CANL) - H56-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H91 No. 3 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to No. 4 Global CAN Junction Connector |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-6 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H91-16 (CANL) - H56-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-2 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H91-12 (CANL) - H56-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to Certification ECU (Smart Key ECU Assembly) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-3 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H91-13 (CANL) - H56-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to Air Conditioning Amplifier Assembly |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-4 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H91-14 (CANL) - H56-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| w/ Seat Position Memory System | A |
| w/o Seat Position Memory System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to Outer Mirror Control ECU Assembly RH |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-5 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H91-15 (CANL) - H56-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H59 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-2 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H91-12 (CANL) - H56-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H48 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to Certification ECU (Smart Key ECU Assembly) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-3 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H91-13 (CANL) - H56-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H62 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to Air Conditioning Amplifier Assembly |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-4 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H91-14 (CANL) - H56-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the J7 outer mirror control ECU assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to Outer Mirror Control ECU Assembly RH |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-5 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H91-15 (CANL) - H56-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H92 No. 4 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to No. 9 Global CAN Junction Connector |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-4 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H92-10 (CANL) - H56-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to No. 3 Global CAN Junction Connector |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-3 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H92-9 (CANL) - H56-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to Main Body ECU (Multiplex Network Body ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-1 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H92-7 (CANL) - H56-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| w/ Headup Display System | A |
| w/o Headup Display System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to Meter Mirror Sub-assembly |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-2 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H92-8 (CANL) - H56-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| w/ Seat Position Memory System | A |
| w/o Seat Position Memory System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to Outer Mirror Control ECU Assembly LH |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-5 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H92-11 (CANL) - H56-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H43 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to Main Body ECU (Multiplex Network Body ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-1 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H92-7 (CANL) - H56-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H31 meter mirror sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to Meter Mirror Sub-assembly |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-2 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H92-8 (CANL) - H56-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the J23 outer mirror control ECU assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to Outer Mirror Control ECU Assembly LH |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-5 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| H92-11 (CANL) - H56-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the M96 No. 9 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
*b | to No. 4 Global CAN Junction Connector |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M96-3 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M96-9 (CANL) - H56-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
*b | to Combination Meter Assembly |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M96-4 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M96-10 (CANL) - H56-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
*b | to Multiplex Network Door ECU |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M96-1 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M96-7 (CANL) - H56-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| w/ Seat Position Memory System | A |
| w/o Seat Position Memory System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
*b | to Position Control ECU Assembly LH |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M96-2 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M96-8 (CANL) - H56-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H21 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
*b | to Combination Meter Assembly |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M96-4 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M96-10 (CANL) - H56-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the W18 multiplex network door ECU connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
*b | to Multiplex Network Door ECU |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M96-1 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M96-7 (CANL) - H56-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the e25 position control ECU assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
*b | to Position Control ECU Assembly LH |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M96-2 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M96-8 (CANL) - H56-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H91 No. 3 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to No. 4 Global CAN Junction Connector |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-6 (CANH) - H91-16 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-2 (CANH) - H91-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to Certification ECU (Smart Key ECU Assembly) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-3 (CANH) - H91-13 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to Air Conditioning Amplifier Assembly |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-4 (CANH) - H91-14 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| w/ Seat Position Memory System | A |
| w/o Seat Position Memory System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to Outer Mirror Control ECU Assembly RH |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-5 (CANH) - H91-15 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H59 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-2 (CANH) - H91-12 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H48 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to Certification ECU (Smart Key ECU Assembly) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-3 (CANH) - H91-13 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H62 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to Air Conditioning Amplifier Assembly |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-4 (CANH) - H91-14 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the J7 outer mirror control ECU assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to Outer Mirror Control ECU Assembly RH |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-5 (CANH) - H91-15 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H92 No. 4 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to No. 9 Global CAN Junction Connector |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-4 (CANH) - H92-10 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to No. 3 Global CAN Junction Connector |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-3 (CANH) - H92-9 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to Main Body ECU (Multiplex Network Body ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-1 (CANH) - H92-7 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| w/ Headup Display System | A |
| w/o Headup Display System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to Meter Mirror Sub-assembly |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-2 (CANH) - H92-8 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| w/ Seat Position Memory System | A |
| w/o Seat Position Memory System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to Outer Mirror Control ECU Assembly LH |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-5 (CANH) - H92-11 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H43 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to Main Body ECU (Multiplex Network Body ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-1 (CANH) - H92-7 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H31 meter mirror sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to Meter Mirror Sub-assembly |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-2 (CANH) - H92-8 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the J23 outer mirror control ECU assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to Outer Mirror Control ECU Assembly LH |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-5 (CANH) - H92-11 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the M96 No. 9 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
*b | to No. 4 Global CAN Junction Connector |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M96-3 (CANH) - M96-9 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
*b | to Combination Meter Assembly |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M96-4 (CANH) - M96-10 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
*b | to Multiplex Network Door ECU |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M96-1 (CANH) - M96-7 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| w/ Seat Position Memory System | A |
| w/o Seat Position Memory System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
*b | to Position Control ECU Assembly LH |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M96-2 (CANH) - M96-8 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H21 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
*b | to Combination Meter Assembly |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M96-4 (CANH) - M96-10 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the W18 multiplex network door ECU connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
*b | to Multiplex Network Door ECU |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M96-1 (CANH) - M96-7 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the e25 position control ECU assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
*b | to Position Control ECU Assembly LH |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M96-2 (CANH) - M96-8 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H91 No. 3 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-2 (CANH) - H91-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 3 Global CAN Junction Connector) |
*b | to No. 4 Global CAN Junction Connector |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H91-6 (CANH) - H91-16 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the H91 No. 3 global CAN junction connector.
Disconnect the H92 No. 4 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to No. 3 Global CAN Junction Connector |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-3 (CANH) - H92-9 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 4 Global CAN Junction Connector) |
*b | to No. 9 Global CAN Junction Connector |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H92-4 (CANH) - H92-10 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the H92 No. 4 global CAN junction connector.
Disconnect the M96 No. 9 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
*b | to No. 4 Global CAN Junction Connector |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M96-3 (CANH) - M96-9 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 9 Global CAN Junction Connector) |
*b | to Combination Meter Assembly |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M96-4 (CANH) - M96-10 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the M96 No. 9 global CAN junction connector.
Disconnect the H21 combination meter assembly connector.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H21-32 (CANH) - H21-31 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the H91 No. 3 global CAN junction connector.
Disconnect the H59 central gateway ECU (network gateway ECU) connector.
| *a | Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H59-15 (CA5H) - H59-16 (CA5L) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG