Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING
RM37A0E _58 Vehicle Interior _086898 INTERIOR PANELS / TRIM _0417354 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  REASSEMBLY  


PROCEDURE

Hide 82171 1.INSTALL NO. 1 ROOF WIRE (for Normal Roof)

a.

Apply double-sided tape as shown in the illustration.

B609160C01
2.25,0.115 5,1.115 2.75,1 3.625,0.969 3.479,0.833 false 3.677,0.25 3.49,0.365 false 4.781,3.26 6.073,3.438 true 3.656,0.896 3.969,1.094 0.313,0.198 10 false *a 3.688,0.146 4,0.344 0.313,0.198 10 false *a 6.104,3.365 6.417,3.563 0.313,0.198 10 false *1
*1 Rear Roof Air Duct - -
*a Marking - -
V100155

Double-sided Tape - -


NOTICE:

Securely attach the double-sided tape.


HINT:

Slide the double-sided tape under the rear roof air duct then press it to attach it.



b.

Align the marking tape (A) on the No. 1 roof wire with the vehicle front side tab of the roof headlining assembly.

B609159C01
3.438,3.573 3.219,3.031 true 6.438,2.677 5.823,2.052 true 3.385,3.583 3.625,3.802 0.24,0.219 10 false *a 4.469,2.552 4.708,2.771 0.24,0.219 10 false *b 1.927,2.396 2.083,2.563 0.156,0.167 10 true *c 1.938,0.823 2.094,0.99 0.156,0.167 10 true *c 6.51,2.604 6.75,2.823 0.24,0.219 10 false *1
*1 Rear Roof Air Duct - -
*a Marking Tape (A) *b Adjustment Area
*c 45° - -
V113147

Rotation Direction - -



c.

Engage each clamp.


d.

Turn the 2 visor connectors clockwise approximately 45° to install them to the roof headlining assembly.


e.

Using wire, pass the No. 1 roof wire between the rear roof air duct and roof headlining assembly.

i.

Secure the wire with a diameter of 2.0 mm (0.0787 in.) to the No. 1 roof wire with vinyl tape as shown in the illustration.

E464022C01
1,0.75 1,0.469 false 1.583,1.583 1.729,1.365 false 5.333,1.833 5.333,1.5 false 5.26,1.854 5.573,2.01 0.313,0.156 10 false *a 0.927,0.771 1.24,0.927 0.313,0.156 10 false *b 1.469,1.594 1.781,1.75 0.313,0.156 10 false *c
*a Vinyl Tape *b Wire
*c Connector - -


NOTICE:

Make sure that the wire is secured with vinyl tape to prevent the wire from separating from the No. 1 roof wire when removing it.


HINT:

As the No. 1 roof wire is likely to be caught in the narrow areas inside the roof headlining assembly, make sure to align in a straight line and cover the edges of the connector with vinyl tape.




f.

Attach the No. 1 roof wire with the double-sided tape.

NOTICE:
·

Securely attach the No. 1 roof wire.

·

If any of the No. 1 roof wire is left loose, it will cause an abnormal noise.

·

Make sure to attach the No. 1 roof wire without leaving any of it loose.



HINT:

Secure the extra length of the No. 1 roof wire in the adjustment area.



g.

Install the No. 1 roof wire to the roof headlining assembly with adhesive tape.

B609157C01
0.167,3.5 7,4.75 6.833,1.25 4.198,4.083 4.51,3.969 false 6.115,4.073 6.427,3.958 false 3.167,4.75 3.167,3.5 false 5.167,4.75 5.167,3.5 false 4.531,3.844 4.844,4.042 0.313,0.198 10 false *1 6.448,3.865 6.76,4.063 0.313,0.198 10 false *1 0.25,3.552 0.563,3.75 0.313,0.198 10 false *a 3.271,3.583 3.583,3.781 0.313,0.198 10 false *b 5.25,3.583 5.563,3.781 0.313,0.198 10 false *c 0.604,4.427 0.917,4.625 0.313,0.198 10 false A 1.271,4.083 1.583,4.281 0.313,0.198 10 false B 2.042,4.427 2.354,4.625 0.313,0.198 10 false C 2.729,4.083 3.042,4.281 0.313,0.198 10 false D 3.74,4.469 4.052,4.667 0.313,0.198 10 false *d 4.458,4.458 4.771,4.656 0.313,0.198 10 false *d
*1 No. 1 Roof Wire - -
*a Adhesive Tape Size *b Correct
*c Incorrect *d 15 mm (0.591 in.) or more
V100155

Adhesive Tape - -


Adhesive Tape Size
Area Dimension
A 20 mm (0.787 in.)
B 80 mm (3.15 in.)
C 80 mm (3.15 in.)
D 80 mm (3.15 in.)

NOTICE:
·

Apply the tape securely in place.

·

Do not touch the adhesive surface when applying the tape to prevent adhesion failure.




Hide 82171 2.INSTALL NO. 1 ROOF WIRE (for Moon Roof)

a.

Apply double-sided tape as shown in the illustration.

B609165C01
2.188,0.271 5.083,1.188 2.896,0.917 3.656,1.083 3.51,0.948 false 3.677,0.375 3.49,0.49 false 4.74,3.188 5.625,3.625 true 3.677,1.01 3.99,1.208 0.313,0.198 10 false *a 3.698,0.271 4.01,0.469 0.313,0.198 10 false *a 5.667,3.542 5.979,3.74 0.313,0.198 10 false *1
*1 Rear Roof Air Duct - -
*a Marking - -
V100155

Double-sided Tape - -


NOTICE:

Securely attach the double-sided tape.


HINT:

Slide the double-sided tape under the rear roof air duct then press it to attach it.



b.

Align the marking tape (A) on the No. 1 roof wire with the vehicle front side tab of the roof headlining assembly.

B609164C01
3.552,4.354 3.354,3.688 true 5.969,3.948 6.76,3.333 6.76,3.333 5.906,2.771 true 2.01,1.469 2.188,1.646 0.177,0.177 10 true *c 2.01,3.073 2.188,3.25 0.177,0.177 10 true *c 3.479,4.354 3.656,4.531 0.177,0.177 10 false *a 4.292,0.135 4.469,0.313 0.177,0.177 10 false *b 6.844,3.25 7.021,3.427 0.177,0.177 10 false *1
*1 Rear Roof Air Duct - -
*a Marking Tape (A) *b Adjustment Area
*c 45° - -
V113147

Rotation Direction
V113148

Lift up in this Direction



c.

Engage each clamp.


d.

Turn the 2 visor connectors clockwise approximately 45° to install them to the roof headlining assembly.


e.

While lifting the rear roof air duct as shown in the illustration, pass the No. 1 roof wire through.

HINT:

Lift up the rear roof air duct to the extent that the No. 1 roof wire can be passed through.



f.

Using wire, pass the No. 1 roof wire between the rear roof air duct and roof headlining assembly.

i.

Secure the wire with a diameter of 2.0 mm (0.0787 in.) to the No. 1 roof wire with vinyl tape as shown in the illustration.

E464022C01
1,0.75 1,0.469 false 1.583,1.583 1.729,1.365 false 5.333,1.833 5.333,1.5 false 5.26,1.854 5.573,2.01 0.313,0.156 10 false *a 0.927,0.771 1.24,0.927 0.313,0.156 10 false *b 1.469,1.594 1.781,1.75 0.313,0.156 10 false *c
*a Vinyl Tape *b Wire
*c Connector - -


NOTICE:

Make sure that the wire is secured with vinyl tape to prevent the wire from separating from the No. 1 roof wire when removing it.


HINT:

As the No. 1 roof wire is likely to be caught in the narrow areas inside the roof headlining assembly, make sure to align in a straight line and cover the edges of the connector with vinyl tape.




g.

Attach the No. 1 roof wire with the double-sided tape.

NOTICE:
·

Securely attach the No. 1 roof wire.

·

If any of the No. 1 roof wire is left loose, it will cause an abnormal noise.

·

Make sure to attach the No. 1 roof wire without leaving any of it loose.



HINT:

Secure the extra length of the No. 1 roof wire in the adjustment area.



h.

Install the No. 1 roof wire to the roof headlining assembly with adhesive tape.

B609162C01
0.167,3.5 7,4.75 6.833,1.25 4.198,4.083 4.51,3.969 false 6.094,4.104 6.406,3.99 false 3.167,4.75 3.167,3.5 false 5.167,4.75 5.167,3.5 false 4.542,3.854 4.854,4.052 0.313,0.198 10 false *1 6.427,3.875 6.74,4.073 0.313,0.198 10 false *1 0.25,3.552 0.563,3.75 0.313,0.198 10 false *a 3.271,3.583 3.583,3.781 0.313,0.198 10 false *b 5.25,3.583 5.563,3.781 0.313,0.198 10 false *c 0.604,4.427 0.917,4.625 0.313,0.198 10 false A 1.271,4.083 1.583,4.281 0.313,0.198 10 false B 2.042,4.427 2.354,4.625 0.313,0.198 10 false C 2.729,4.083 3.042,4.281 0.313,0.198 10 false D 3.74,4.458 4.052,4.656 0.313,0.198 10 false *d 4.438,4.469 4.75,4.667 0.313,0.198 10 false *d
*1 No. 1 Roof Wire - -
*a Adhesive Tape Size *b Correct
*c Incorrect *d 15 mm (0.591 in.) or more
V100155

Adhesive Tape - -


Adhesive Tape Size
Area Dimension
A 20 mm (0.787 in.)
B 80 mm (3.15 in.)
C 80 mm (3.15 in.)
D 80 mm (3.15 in.)

NOTICE:
·

Apply the tape securely in place.

·

Do not touch the adhesive surface when applying the tape to prevent adhesion failure.




Hide 82171 3.INSTALL NO. 1 ROOF WIRE (for Panoramic Moon Roof)

a.

Apply double-sided tape as shown in the illustration.

B609170C01
2.188,0.271 5.083,1.188 2.896,0.917 3.656,1.083 3.51,0.948 false 3.677,0.375 3.49,0.49 false 4.781,3.188 5.604,3.677 true 3.677,1.01 3.99,1.208 0.313,0.198 10 false *a 3.698,0.271 4.01,0.469 0.313,0.198 10 false *a 5.635,3.594 5.948,3.792 0.313,0.198 10 false *1
*1 Rear Roof Air Duct - -
*a Marking - -
V100155

Double-sided Tape - -


NOTICE:

Securely attach the double-sided tape.


HINT:

Slide the double-sided tape under the rear roof air duct then press it to attach it.



b.

Align the marking tape (A) on the No. 1 roof wire with the vehicle front side tab of the roof headlining assembly.

B609169C01
3.406,3.552 3.219,3.021 true 6.573,2.615 5.906,2.042 true 3.333,3.563 3.542,3.75 0.208,0.188 10 false *a 4.771,2.594 5.01,2.813 0.24,0.219 10 false *b 1.927,2.417 2.083,2.583 0.156,0.167 10 true *c 1.917,0.823 2.073,0.99 0.156,0.167 10 true *c 3.49,0.917 3.729,1.135 0.24,0.219 10 false *b 6.604,2.542 6.813,2.729 0.208,0.188 10 false *1
*1 Rear Roof Air Duct - -
*a Marking Tape (A) *b Adjustment Area
*c 45° - -
V113147

Rotation Direction - -



c.

Engage each clamp.


d.

Turn the 2 visor connectors clockwise approximately 45° to install them to the roof headlining assembly.


e.

Using wire, pass the No. 1 roof wire between the rear roof air duct and roof headlining assembly.

i.

Secure the wire with a diameter of 2.0 mm (0.0787 in.) to the No. 1 roof wire with vinyl tape as shown in the illustration.

E464022C01
1,0.75 1,0.469 false 1.583,1.583 1.729,1.365 false 5.333,1.833 5.333,1.5 false 5.26,1.854 5.573,2.01 0.313,0.156 10 false *a 0.927,0.771 1.24,0.927 0.313,0.156 10 false *b 1.469,1.594 1.781,1.75 0.313,0.156 10 false *c
*a Vinyl Tape *b Wire
*c Connector - -


NOTICE:

Make sure that the wire is secured with vinyl tape to prevent the wire from separating from the No. 1 roof wire when removing it.


HINT:

As the No. 1 roof wire is likely to be caught in the narrow areas inside the roof headlining assembly, make sure to align in a straight line and cover the edges of the connector with vinyl tape.




f.

Attach the No. 1 roof wire with the double-sided tape.

NOTICE:
·

Securely attach the No. 1 roof wire.

·

If any of the No. 1 roof wire is left loose, it will cause an abnormal noise.

·

Make sure to attach the No. 1 roof wire without leaving any of it loose.



HINT:

Secure the extra length of the No. 1 roof wire in the adjustment area.



g.

Install the No. 1 roof wire to the roof headlining assembly with adhesive tape.

B609167C01
0.167,3.583 7,4.75 6.833,1.167 3.167,4.75 3.167,3.583 false 5.083,4.75 5.083,3.583 false 4.167,4.104 4.531,3.948 false 6.083,4.094 6.448,3.938 false 0.229,3.635 0.542,3.833 0.313,0.198 10 false *a 3.219,3.635 3.531,3.833 0.313,0.198 10 false *b 5.146,3.625 5.458,3.823 0.313,0.198 10 false *c 0.573,4.448 0.729,4.646 0.156,0.198 10 false A 1.26,4.073 1.417,4.271 0.156,0.198 10 false B 2.021,4.458 2.177,4.656 0.156,0.198 10 false C 2.698,4.073 2.854,4.271 0.156,0.198 10 false D 4.552,3.854 4.865,4.052 0.313,0.198 10 false *1 6.479,3.854 6.792,4.052 0.313,0.198 10 false *1 3.74,4.458 4.052,4.656 0.313,0.198 10 false *d 4.458,4.458 4.771,4.656 0.313,0.198 10 false *d
*1 No. 1 Roof Wire - -
*a Adhesive Tape Size *b Correct
*c Incorrect *d 15 mm (0.591 in.) or more
V100155

Adhesive Tape - -


Adhesive Tape Size
Area Dimension
A 20 mm (0.787 in.)
B 80 mm (3.15 in.)
C 80 mm (3.15 in.)
D 80 mm (3.15 in.)

NOTICE:
·

Apply the tape securely in place.

·

Do not touch the adhesive surface when applying the tape to prevent adhesion failure.




Hide 4.INSTALL NO. 3 ROOF HEADLINING SUPPORT (except Panoramic Moon Roof)

a.
B565658C01
0.281,0.708 0.604,0.823 false 0.125,0.583 0.438,0.74 0.313,0.156 10 false *a
*a Marking
V100155

Hot-melt Glue


Using hot-melt glue, install a new No. 3 roof headlining support to the roof headlining assembly.

HINT:

Install the No. 3 roof headlining support so that it is within the markings shown in the illustration.



Hide 81390C 5.INSTALL SPOT LIGHT ASSEMBLY LH (for Panoramic Moon Roof)

Hide 81360K 6.INSTALL SPOT LIGHT ASSEMBLY RH (for Panoramic Moon Roof)

HINT:

Use the same procedure as for the LH side.


Hide 7.INSTALL REAR WASHER HOSE ASSEMBLY

a.

for Normal Roof:

i.

Apply butyl tape as shown in the illustration.

B609084C01
2.167,0.083 5,1.25 2.833,1.167 3.781,1.125 3.563,0.917 false 3.583,0.458 3.813,0.208 false 5.365,2.552 4.792,2.104 true 3.813,1.052 4.125,1.25 0.313,0.198 10 false *a 3.844,0.115 4.156,0.313 0.313,0.198 10 false *a 5.396,2.479 5.708,2.677 0.313,0.198 10 false *1
*1 Rear Roof Air Duct - -
*a Marking - -
V100155

Butyl Tape - -


NOTICE:

Securely attach the butyl tape.


HINT:

Slide the butyl tape under the rear roof air duct then press it to attach it.



ii.

Align the edge of the marking tape on the rear washer hose assembly from the vehicle front side tab of the roof headlining assembly as shown in the illustration.

B609083C01
5.615,1.5 5.365,0.802 true 3.698,2.219 3.917,2.417 0.219,0.198 10 true *a 5.542,1.51 5.76,1.708 0.219,0.198 10 false *1
*1 Rear Roof Air Duct - -
*a Adjustment Area - -
V100143

Marking Tape
V100155

Adhesive Tape



iii.

Using wire, pass the rear washer hose assembly between the rear roof air duct and roof headlining assembly.

1.

Secure the wire with a diameter of 2.0 mm (0.0787 in.) to the rear washer hose assembly with vinyl tape as shown in the illustration.

E464023C01
1,0.75 1,0.469 false 1.583,1.583 1.729,1.365 false 5.333,1.833 5.333,1.5 false 5.26,1.854 5.573,2.01 0.313,0.156 10 false *a 0.927,0.771 1.24,0.927 0.313,0.156 10 false *b 1.469,1.594 1.781,1.75 0.313,0.156 10 false *c
*a Vinyl Tape *b Wire
*c Joint - -


NOTICE:

Make sure that the wire is secured with vinyl tape to prevent the wire from separating from the rear washer hose assembly when removing it.


HINT:

As the rear washer hose assembly is likely to be caught in the narrow areas inside the roof headlining assembly, make sure to align in a straight line and cover the edges of the joint with vinyl tape.




iv.

Align the edge of the joint to the rear washer hose assembly from the vehicle rear side of the roof headlining assembly as shown in the illustration.


v.

Attach the rear washer hose assembly with the butyl tape.

NOTICE:
·

Securely attach the rear washer hose assembly.

·

If any of the rear washer hose assembly is left loose, it will cause an abnormal noise.

·

Make sure to attach the rear washer hose assembly without leaving any of it loose.



HINT:

Secure the extra length of the rear washer hose assembly in the adjustment area using the adhesive tape as shown in the illustration.



vi.

Install the rear washer hose assembly with adhesive tape.



b.

for Moon Roof:

i.

Apply butyl tape as shown in the illustration.

B609092C01
2.167,0.167 5,1.333 2.833,1.167 3.521,0.521 3.792,0.292 false 3.563,0.979 3.813,1.198 false 4.615,1.927 5.823,1.802 true 3.813,0.198 4.125,0.396 0.313,0.198 10 false *a 3.833,1.146 4.146,1.344 0.313,0.198 10 false *a 5.854,1.708 6.167,1.906 0.313,0.198 10 false *1
*1 Rear Roof Air Duct - -
*a Marking - -
V100155

Butyl Tape - -


NOTICE:

Securely attach the butyl tape.


HINT:

Slide the butyl tape under the rear roof air duct then press it to attach it.



ii.

Align the edge of the marking tape on the rear washer hose assembly from the vehicle front side tab of the roof headlining assembly as shown in the illustration.

B609091C01
4.021,0.729 5.75,1.354 5.75,1.354 5.313,1.99 true 3.656,3.344 3.854,3.521 0.198,0.177 10 true *a 5.792,1.271 5.99,1.448 0.198,0.177 10 false *1
*1 Rear Roof Air Duct - -
*a Adjustment Area - -
V100143

Marking Tape
V100155

Adhesive Tape
V113147

Lift up in this Direction - -



iii.

While lifting the rear roof air duct as shown in the illustration, pass the rear washer hose assembly through.

HINT:

Lift up the rear roof air duct to the extent that the rear washer hose assembly can be passed through.



iv.

Using wire, pass the rear washer hose assembly between the rear roof air duct and roof headlining assembly.

1.

Secure the wire with a diameter of 2.0 mm (0.0787 in.) to the rear washer hose assembly with vinyl tape as shown in the illustration.

E464023C01
1,0.75 1,0.469 false 1.583,1.583 1.729,1.365 false 5.333,1.833 5.333,1.5 false 5.26,1.854 5.573,2.01 0.313,0.156 10 false *a 0.927,0.771 1.24,0.927 0.313,0.156 10 false *b 1.469,1.594 1.781,1.75 0.313,0.156 10 false *c
*a Vinyl Tape *b Wire
*c Joint - -


NOTICE:

Make sure that the wire is secured with vinyl tape to prevent the wire from separating from the rear washer hose assembly when removing it.


HINT:

As the rear washer hose assembly is likely to be caught in the narrow areas inside the roof headlining assembly, make sure to align in a straight line and cover the edges of the joint with vinyl tape.




v.

Align the edge of the joint to the rear washer hose assembly from the vehicle rear side of the roof headlining assembly as shown in the illustration.


vi.

Attach the rear washer hose assembly with the butyl tape.

NOTICE:
·

Securely attach the rear washer hose assembly.

·

If any of the rear washer hose assembly is left loose, it will cause an abnormal noise.

·

Make sure to attach the rear washer hose assembly without leaving any of it loose.



HINT:

Secure the extra length of the rear washer hose assembly in the adjustment area using the adhesive tape as shown in the illustration.



vii.

Install the rear washer hose assembly with adhesive tape.



c.

for Panoramic Moon Roof:

i.

Apply butyl tape as shown in the illustration.

B609105C01
2.083,0.167 5,1.333 2.917,1.167 3.521,0.521 3.792,0.292 false 3.563,0.979 3.813,1.198 false 5.802,1.667 4.76,1.896 true 3.813,0.198 4.125,0.396 0.313,0.198 10 false *a 3.833,1.146 4.146,1.344 0.313,0.198 10 false *a 5.833,1.573 6.063,1.729 0.229,0.156 10 false *1
*1 Rear Roof Air Duct - -
*a Marking - -
V100155

Butyl Tape - -


NOTICE:

Securely attach the butyl tape.


HINT:

Slide the butyl tape under the rear roof air duct then press it to attach it.



ii.

Align the edge of the marking tape on the rear washer hose assembly from the vehicle front side tab of the roof headlining assembly as shown in the illustration.

B609099C01
5.458,0.542 6.74,0.323 true 3.698,2.208 3.917,2.406 0.219,0.198 10 true *a 6.771,0.229 7.083,0.427 0.313,0.198 10 false *1
*1 Rear Roof Air Duct - -
*a Adjustment Area - -
V100143

Marking Tape
V100155

Adhesive Tape



iii.

Using wire, pass the rear washer hose assembly between the rear roof air duct and roof headlining assembly.

1.

Secure the wire with a diameter of 2.0 mm (0.0787 in.) to the rear washer hose assembly with vinyl tape as shown in the illustration.

E464023C01
1,0.75 1,0.469 false 1.583,1.583 1.729,1.365 false 5.333,1.833 5.333,1.5 false 5.26,1.854 5.573,2.01 0.313,0.156 10 false *a 0.927,0.771 1.24,0.927 0.313,0.156 10 false *b 1.469,1.594 1.781,1.75 0.313,0.156 10 false *c
*a Vinyl Tape *b Wire
*c Joint - -


NOTICE:

Make sure that the wire is secured with vinyl tape to prevent the wire from separating from the rear washer hose assembly when removing it.


HINT:

As the rear washer hose assembly is likely to be caught in the narrow areas inside the roof headlining assembly, make sure to align in a straight line and cover the edges of the joint with vinyl tape.




iv.

Align the edge of the joint to the rear washer hose assembly from the vehicle rear side of the roof headlining assembly as shown in the illustration.


v.

Attach the rear washer hose assembly with the butyl tape.

NOTICE:
·

Securely attach the rear washer hose assembly.

·

If any of the rear washer hose assembly is left loose, it will cause an abnormal noise.

·

Make sure to attach the rear washer hose assembly without leaving any of it loose.



HINT:

Secure the extra length of the rear washer hose assembly in the adjustment area using the adhesive tape as shown in the illustration.



vi.

Install the rear washer hose assembly with adhesive tape.



Hide 86101D 8.INSTALL NO. 3 ANTENNA CORD SUB-ASSEMBLY (for Normal Roof)

Hide 86101D 9.INSTALL NO. 3 ANTENNA CORD SUB-ASSEMBLY (for Moon Roof)

Hide 86101D 10.INSTALL NO. 3 ANTENNA CORD SUB-ASSEMBLY (for Panoramic Moon Roof)

Hide 11.INSTALL INNER ROOF SIDE SEAL (for Panoramic Moon Roof)

a.

Remove the release paper from a new inner roof side seal.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



b.

Install the inner roof side seal to the roof headlining assembly as shown in the illustration.

NOTICE:

Make sure to firmly press the double-sided tape portion of the inner roof side seal to securely attach it.


B603050C02
5.781,0.844 5.563,0.594 false 1.302,1.646 1.458,1.844 0.156,0.198 10 true A 1.979,1.656 2.135,1.854 0.156,0.198 10 true A 4.125,0.458 4.896,0.656 0.771,0.198 10 false A - A 5.385,0.458 5.698,0.656 0.313,0.198 10 false *a
*a R End - -



Hide 12.INSTALL FRONT DOOR VENT SEAL

a.

Remove the release paper from 2 new front door vent seals.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



b.
B603048C02
1.177,1.042 1.313,1.198 true 2.396,0.844 2.313,1 true 1.219,1.177 1.427,1.375 0.208,0.198 10 true *a 2.208,1.01 2.417,1.208 0.208,0.198 10 true *a
*a Marking


Install the 2 front door vent seals to the roof headlining assembly as shown in the illustration.

NOTICE:

Make sure to firmly press the double-sided tape portion of the front door vent seal to securely attach it.