The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear axle hub bolt removal/installation are shown below.
After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.
When removing or installing the rear disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.
While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1.DISABLE BRAKE CONTROL (for HV Model)
Click hereBrake>BRAKE (REAR)>REAR BRAKE>REMOVAL
2.REMOVE REAR WHEEL
890C0A
3.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
47850
4.SEPARATE REAR DISC BRAKE CYLINDER ASSEMBLY
Hold the 2 rear disc brake cylinder slide pins and remove the 2 bolts and separate the rear disc brake cylinder assembly.
Use wire or an equivalent tool to keep the rear disc brake cylinder assembly from hanging by the rear flexible hose.
5.REMOVE REAR DISC BRAKE CYLINDER MOUNTING WITH BRAKE PAD
Remove the 2 bolts and rear disc brake cylinder mounting with the 2 rear disc brake pads from the rear axle carrier sub-assembly.
42431
6.REMOVE REAR DISC
Click hereBrake>BRAKE (REAR)>REAR BRAKE>REMOVAL
42312E
7.REMOVE REAR AXLE HUB BOLT
| *a | Service Nut |
Temporarily install 2 service nuts to the rear axle hub bolts as shown in the illustration.
Thread diameter: 12.0 mm (0.472 in.)
Thread pitch: 1.5 mm (0.0591 in.)
Install the service nuts to prevent damage to the rear axle hub bolts.
Using SST and a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, remove the rear axle hub bolt.
Do not damage the threads of the rear axle hub bolts.
42312E
8.INSTALL REAR AXLE HUB BOLT
| *a | Service Nut |
| *b | Washer |
Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.
Install a washer and service nut to the rear axle hub bolt as shown in the illustration.
Thread diameter: 12.0 mm (0.472 in.)
Thread pitch: 1.5 mm (0.0591 in.)
Recommended washer thickness is 5 mm (0.197 in.) or more.
Using a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the service nut.
Install the service nuts to prevent damage to the rear axle hub bolts.
Do not damage the threads of the rear axle hub bolts.
Remove the 3 service nuts and washer from the 3 rear axle hub bolts.
42431
9.INSTALL REAR DISC
10.INSTALL REAR DISC BRAKE CYLINDER MOUNTING WITH BRAKE PAD
Install the rear disc brake cylinder mounting with the 2 rear disc brake pads to the rear axle carrier sub-assembly with the 2 bolts.
Keep the friction surfaces of the rear disc brake pads and rear disc free from oil and grease.
47850
11.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY
Hold the 2 rear disc brake cylinder slide pins, and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with 2 new bolts.
890C0A
12.CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
13.INSTALL REAR WHEEL
14.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for HV Model)
Connect the reservoir level switch connector.
Install the brake master cylinder reservoir assembly to the reservoir bracket with the bolt and nut.
Engage the clamp to install the wire harness to the brake master cylinder reservoir assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>INSTALLATION
Turn the ignition switch to ON (READY).
Depress the brake pedal and release it.