Home › Engine / Hybrid System › 2GR-FKS (FUEL) › FUEL TANK › 2020.02–2020.11
RM37A0E _51 Engine / Hybrid System _086852 2GR-FKS FUEL _0417515 FUEL TANK A

2GR-FKS FUEL  FUEL TANK  INSTALLATION  


PROCEDURE

Hide 77651A 1.INSTALL NO. 1 FUEL TANK CUSHION

HINT:

Perform this procedure only when replacement of the No. 1 fuel tank cushion is necessary.


a.

Install a new No. 1 fuel tank cushion to the fuel tank sub-assembly.


Hide 77656B 2.INSTALL NO. 6 FUEL TANK CUSHION

HINT:

Perform this procedure only when replacement of the No. 6 fuel tank cushion is necessary.


a.

Install 3 new No. 6 fuel tank cushions to the fuel tank sub-assembly.


Hide 77642A 3.INSTALL NO. 2 FUEL TANK PROTECTOR

a.

Install the No. 2 fuel tank protector to the fuel tank sub-assembly with the clip.


Hide 77285F 4.INSTALL NO. 1 FUEL TUBE CLAMP

a.

Engage the clamp to install the No. 1 fuel tube clamp to the fuel tank sub-assembly.


Hide 77018E 5.INSTALL FUEL TANK EVAPORATION VENT TUBE SUB-ASSEMBLY

a.

Engage the 4 clamps to install the fuel tank evaporation vent tube sub-assembly to the fuel tank sub-assembly.


Hide 77209F 6.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Engage the 3 clamps to install the fuel tank main tube sub-assembly to the fuel tank sub-assembly.


Hide 77001A 7.INSTALL FUEL TANK SUB-ASSEMBLY

CAUTION:
A344817

The fuel tank sub-assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank sub-assembly may fall off the engine lifter.


a.

Set the fuel tank sub-assembly on an engine lifter.

NOTICE:

Using height adjustment attachments and plate lift attachments, keep the fuel tank sub-assembly horizontal.



b.
A458386N01
2.625,0.615 2.781,0.813 0.156,0.198 10 true A 0.813,1.625 0.969,1.823 0.156,0.198 10 true B 0.646,2.302 0.802,2.5 0.156,0.198 10 true C 2.396,2.448 2.552,2.646 0.156,0.198 10 true B 0.75,1.167 0.906,1.365 0.156,0.198 10 true A

Using the engine lifter, slowly raise the fuel tank sub-assembly, and then temporarily install the fuel tank sub-assembly, No. 1 fuel tank band sub-assembly and No. 2 fuel tank band sub-assembly with the 5 bolts.

Bolt Length:
Bolt Width Across Flats
A 14 mm (0.551 in.)
B 12 mm (0.472 in.)
C 12 mm (0.472 in.) or 14 mm (0.551 in.)


NOTICE:
·

Be careful not to drop the fuel tank sub-assembly.

·

When installing the fuel tank sub-assembly, tilt it slightly to prevent it from interfering with the surrounding parts.




c.
A458386N02
2.375,2.479 2.531,2.677 0.156,0.198 10 true 1 0.667,2.302 0.823,2.5 0.156,0.198 10 true 2 0.833,1.656 0.99,1.854 0.156,0.198 10 true 3 2.604,0.615 2.76,0.813 0.156,0.198 10 true 4 0.75,1.167 0.906,1.365 0.156,0.198 10 true 5

Tighten the 5 bolts in the order shown in the illustration.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


d.

Connect the fuel tank breather tube sub-assembly to the fuel tank filler pipe sub-assembly.

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77213B 8.CONNECT FUEL TANK TO FILLER PIPE HOSE

a.

Connect the fuel tank to filler pipe hose to the fuel tank sub-assembly and tighten the clamp to secure it.


Hide 77209F 9.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Connect the fuel tank main tube sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77018E 10.CONNECT FUEL TANK EVAPORATION VENT TUBE SUB-ASSEMBLY

a.

Engage the clamp to connect the fuel tank evaporation vent tube sub-assembly to the canister (charcoal canister assembly).

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 51206A 11.INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY

Hide 58398F 12.INSTALL NO. 1 FLOOR UNDER COVER

a.
A458394N01
0.979,2.76 1.135,2.958 0.156,0.198 10 true A 0.969,1.979 1.125,2.177 0.156,0.198 10 true A 1.052,0.969 1.208,1.167 0.156,0.198 10 true A 0.979,1.365 1.135,1.563 0.156,0.198 10 true A 3.208,0.531 3.365,0.729 0.156,0.198 10 true B 1.281,0.573 1.438,0.771 0.156,0.198 10 true F 2.677,2.25 2.833,2.448 0.156,0.198 10 true F 3.01,1 3.167,1.198 0.156,0.198 10 true C 2.229,0.24 2.385,0.438 0.156,0.198 10 true F 1.125,2.438 1.281,2.635 0.156,0.198 10 true F 2.969,1.563 3.125,1.76 0.156,0.198 10 true D 1.854,3.229 2,3.406 0.146,0.177 10 true E

Install the No. 1 floor under cover with the 4 grommets (F), clip (C), clip (D) and clip (E).


b.

Install the 4 bolts (A) and screw (B).

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 58166A 13.INSTALL FRONT FLOOR COVER LH

a.
A458393N01
2.302,0.219 2.458,0.417 0.156,0.198 10 true A 2.635,1.104 2.792,1.302 0.156,0.198 10 true A 0.958,1.729 1.115,1.927 0.156,0.198 10 true A 0.76,2.635 0.917,2.833 0.156,0.198 10 true A 0.875,0.542 1.031,0.74 0.156,0.198 10 true B 3.177,1.865 3.333,2.063 0.156,0.198 10 true B 3.177,2.542 3.333,2.74 0.156,0.198 10 true B 1.135,3.24 1.281,3.417 0.146,0.177 10 true B 1.729,3.24 1.875,3.417 0.146,0.177 10 true B 2.354,3.24 2.5,3.417 0.146,0.177 10 true B 2.948,1.438 3.104,1.635 0.156,0.198 10 true D 1.656,1.49 1.813,1.688 0.156,0.198 10 true D 1.76,2.167 1.917,2.365 0.156,0.198 10 true C

Install the front floor cover LH with the 2 grommets (D) and clip (C).


b.

Install the 4 bolts (A) and 6 screws (B).

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 77020A 14.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 15.ADD FUEL