1.INSTALL HOLE PLUG
Install the 13 hole plugs to the rear suspension member sub-assembly as shown in the illustration.
The upper and lower hole plug shapes are different.
52271D
2.INSTALL REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for LH Side)
| *a | View from Underneath |
|
Front of the Vehicle |
|
Outside of the Vehicle |
Confirm the installation direction and temporarily install a new rear suspension member front body mounting cushion.
Position the rear suspension member front body mounting cushion in the correct direction.
Do not apply lubricant to the outer sleeve of the rear suspension member front body mounting cushion.
Install SST as shown in the illustration.
Apply molybdenum grease to the threads and tip of the SST center bolt before use.
Use SST with the "F" mark facing the rear suspension member front body mounting cushion.
| *a | Hold |
| *b | Turn |
Using SST, install the rear suspension member front body mounting cushion until there is no clearance between the rear suspension member sub-assembly and rear suspension member front body mounting cushion.
If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.
Remove SST from the rear suspension member sub-assembly.
52271D
3.INSTALL REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for RH Side)
| *a | View from Underneath |
|
Front of the Vehicle |
|
Outside of the Vehicle |
Confirm the installation direction and temporarily install a new rear suspension member front body mounting cushion.
Position the rear suspension member front body mounting cushion in the correct direction.
Do not apply lubricant to the outer sleeve of the rear suspension member front body mounting cushion.
Install SST as shown in the illustration.
Apply molybdenum grease to the threads and tip of the SST center bolt before use.
Use SST with the "F" mark facing the rear suspension member front body mounting cushion.
| *a | Hold |
| *b | Turn |
Using SST, install the rear suspension member front body mounting cushion until there is no clearance between the rear suspension member sub-assembly and rear suspension member front body mounting cushion.
If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.
Remove SST from the rear suspension member sub-assembly.
52276A
4.INSTALL REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION LH
| *a | View from Underneath |
| *b | 15° |
|
Front of the Vehicle |
|
Outside of the Vehicle |
Confirm the installation direction and temporarily install a new rear suspension member rear body mount cushion LH.
Position the rear suspension member rear body mount cushion LH in the correct direction.
Do not apply lubricant to the outer sleeve of the rear suspension member rear body mount cushion LH.
Install SST as shown in the illustration.
Apply molybdenum grease to the threads and tip of the SST center bolt before use.
Use SST with the "F" mark facing the rear suspension member rear body mount cushion LH.
| *a | Hold |
| *b | Turn |
Using SST, install the rear suspension member rear body mount cushion LH until there is no clearance between the rear suspension member sub-assembly and rear suspension member rear body mount cushion LH.
If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.
Remove SST from the rear suspension member sub-assembly.
52275B
5.INSTALL REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION RH
| *a | View from Underneath |
|
Front of the Vehicle |
|
Outside of the Vehicle |
Confirm the installation direction and temporarily install a new rear suspension member rear body mount cushion RH.
Position the rear suspension member rear body mount cushion RH in the correct direction.
Do not apply lubricant to the outer sleeve of the rear suspension member rear body mount cushion RH.
Install SST as shown in the illustration.
Apply molybdenum grease to the threads and tip of the SST center bolt before use.
Use SST with the "F" mark facing the rear suspension member rear body mount cushion RH.
| *a | Hold |
| *b | Turn |
Using SST, install the rear suspension member rear body mount cushion RH until there is no clearance between the rear suspension member sub-assembly and rear suspension member rear body mount cushion RH.
If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.
Remove SST from the rear suspension member sub-assembly.
48790
6.INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH
48770A
7.INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
52272
8.INSTALL REAR SUSPENSION MEMBER UPPER STOPPER
Install the 2 rear suspension member upper stoppers to the rear suspension member sub-assembly.
52278A
9.INSTALL REAR SUSPENSION MEMBER LOWER STOPPER RETAINER
Install the 2 rear suspension member lower stopper retainers to the rear suspension member sub-assembly.
51206A
10.INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY
| *a | Engine Lifter |
| *b | Attachment |
| *c | Wooden Block |
|
Attachment and Wooden Block Placement Location |
Using an engine lifter, 2 attachments and 2 wooden blocks or equivalent tools, support the rear suspension member sub-assembly, and raise the rear suspension member sub-assembly until there is no clearance between the rear suspension member sub-assembly and vehicle body.
The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.
If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.
Use attachments and wooden blocks to keep the rear suspension member sub-assembly level.
Keep supporting the rear suspension member sub-assembly until the installation has been completed.
Install the rear suspension member sub-assembly with the 2 rear lower suspension braces, rear lower suspension member stopper LH and rear lower suspension member stopper RH, with the 4 bolts and 2 nuts.
| *1 | Rear Lower Suspension Brace | - | - |
Be sure to install the rear suspension member sub-assembly with the rear lower suspension braces facing in the correct direction as shown in the illustration.
82164
11.INSTALL FRAME WIRE
Install the frame wire to the rear suspension member sub-assembly with the bolt and clamp.
41651
12.INSTALL REAR NO. 1 DIFFERENTIAL MOUNT CUSHION
41110
13.INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY (for Dynamic Torque Control AWD)
41110
14.INSTALL TORQUE VECTORING DIFFERENTIAL CARRIER ASSEMBLY (for Dynamic Torque Vectoring AWD)
42341C
15.INSTALL REAR DRIVE SHAFT LH SNAP RING
42341B
16.INSTALL REAR DRIVE SHAFT RH SNAP RING
Perform the same procedure as for the LH side.
42340B
17.INSTALL REAR DRIVE SHAFT ASSEMBLY LH
42330
18.INSTALL REAR DRIVE SHAFT ASSEMBLY RH
Perform the same procedure as for the LH side.
48790
19.TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH
Using a brass bar and a hammer, push out the bushing until it is positioned as shown in the illustration.
Pushing out the bushing makes it easier to connect the rear upper control arm assembly LH.
Temporarily install the rear axle carrier sub-assembly to the rear upper control arm assembly with the bolt and nut.
Insert the bolt with the threaded end facing the rear of the vehicle.
Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.
48770A
20.TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
48720A
21.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH
48710A
22.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
48740F
23.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH
48730F
24.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
48258C
25.INSTALL REAR LOWER COIL SPRING INSULATOR LH
48258B
26.INSTALL REAR LOWER COIL SPRING INSULATOR RH
Perform the same procedure as for the LH side.
48231B
27.INSTALL REAR COIL SPRING LH
48231A
28.INSTALL REAR COIL SPRING RH
Perform the same procedure as for the LH side.
48835
29.INSTALL REAR LOWER STABILIZER BRACKET
48812
30.INSTALL REAR STABILIZER BAR
31.TEMPORARILY INSTALL REAR STABILIZER LINK ASSEMBLY LH
32.TEMPORARILY INSTALL REAR STABILIZER LINK ASSEMBLY RH
Perform the same procedure as for the LH side.
89544E
33.INSTALL REAR SKID CONTROL SENSOR LH
89544D
34.INSTALL REAR SKID CONTROL SENSOR RH
Perform the same procedure as for the LH side.
890C0A
35.CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
Connect the No. 2 parking brake wire assembly connector to the rear skid control sensor.
890C0
36.CONNECT NO. 1 PARKING BRAKE WIRE ASSEMBLY
Perform the same procedure as for the LH side.
42312B
37.INSTALL REAR AXLE SHAFT NUT LH
42311N
38.INSTALL REAR AXLE SHAFT NUT RH
Perform the same procedure as for the LH side.
47319F
39.CONNECT REAR FLEXIBLE HOSE LH
Connect the rear flexible hose LH to the rear upper control arm assembly LH with the bolt.
47318F
40.CONNECT REAR FLEXIBLE HOSE RH
Perform the same procedure as for the LH side.
41.STABILIZE SUSPENSION
48720A
42.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH
48710A
43.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
48740F
44.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH
Install the rear No. 2 suspension arm assembly LH (rear axle carrier sub-assembly side) with the bolt.
Click hereSuspension>REAR SUSPENSION>REAR LOWER ARM>INSTALLATION
48730F
45.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
46.INSTALL REAR STABILIZER LINK ASSEMBLY LH
47.INSTALL REAR STABILIZER LINK ASSEMBLY RH
Perform the same procedure as for the LH side.
48790
48.INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH
Install the rear upper control arm assembly to the rear axle carrier sub-assembly with the bolt.
Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.
48770A
49.INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
48738
50.INSTALL REAR SUSPENSION ARM COVER LH
48737
51.INSTALL REAR SUSPENSION ARM COVER RH
Perform the same procedure as for the LH side.
37100
52.INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
17430
53.INSTALL TAIL EXHAUST PIPE ASSEMBLY
54.INSTALL REAR WHEEL
48740F
55.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH
Install the rear No. 2 suspension arm assembly LH (rear suspension member sub-assembly side) with the nut.
Click hereSuspension>REAR SUSPENSION>REAR LOWER ARM>INSTALLATION
48730F
56.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
57.ADD DIFFERENTIAL OIL
for Dynamic Torque Control AWD: Click hereGeneral>MAINTENANCE>DIFFERENTIAL OIL>REPLACEMENT
for Dynamic Torque Vectoring AWD: Click hereGeneral>MAINTENANCE>DIFFERENTIAL OIL>REPLACEMENT
58. INSPECT FOR DIFFERENTIAL OIL LEAK
59.INSPECT FOR EXHAUST GAS LEAK
60.INSPECT AND ADJUST REAR WHEEL ALIGNMENT
61.CHECK FOR SPEED SENSOR SIGNAL