Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM37A0E _58 Vehicle Interior _086884 DOOR LOCK _0417738 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Only Back Door cannot be Opened  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives signals from the back door opener switch assembly. When a signal received is the main body ECU (multiplex network body ECU) activates the back door lock motor.

WIRING DIAGRAM

B533169E05
1.333,0.604 1.49,0.802 0.156,0.198 10 false 2 1.521,0.604 2.01,0.854 0.49,0.25 10 false ACT- 2.729,0.615 3.219,0.865 0.49,0.25 10 false ACT+ 3.177,0.604 3.333,0.802 0.156,0.198 10 false 1 1.448,1.188 1.917,1.469 0.469,0.281 10 false W12 1.438,1.385 3.385,1.802 1.948,0.417 10 false Back Door Lock with Courtesy Light Switch Assembly 4.115,1.083 4.427,1.302 0.313,0.219 10 false 4D 4.156,0.5 4.469,0.719 0.313,0.219 10 false 20 3.698,1.229 5.281,1.583 1.583,0.354 10 false Instrument Panel Junction Block Assembly 5.385,0.698 5.875,0.948 0.49,0.25 10 false TR+ 4.469,2.042 6.146,2.375 1.677,0.333 10 false Main Body ECU (Multiplex Network Body ECU) 1.875,3.344 2.104,3.573 0.229,0.229 10 false E 2.906,3.333 3.135,3.563 0.229,0.229 10 false UL 1.708,3.344 1.865,3.542 0.156,0.198 10 false 2 3.156,3.323 3.313,3.521 0.156,0.198 10 false 3 5.083,3.333 5.396,3.552 0.313,0.219 10 false 26 5.344,3.417 5.906,3.646 0.563,0.229 10 false TSW5 1.438,3.823 2.292,4.042 0.854,0.219 10 false W11 1.438,3.969 4.063,4.292 2.625,0.323 10 false Back Door Opener Switch Assembly 5.135,4.115 6,4.292 0.865,0.177 10 false M5 5.135,4.292 6.667,4.813 1.531,0.521 10 false Certification ECU (Smart Key ECU Assembly) 0.792,5.302 2.948,5.563 2.156,0.26 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

The power door lock control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power door lock control system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

The auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (TRUNK AND BACK-DOOR OPEN)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Trunk and Back-Door Open Back door lock motor OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Trunk and Back-Door Open
50004 123 3
OK:

The back door lock with courtesy light switch assembly unlatches when ON is selected.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (TR/B-DOOR LOCK SW)

NG

5.INSPECT BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY
2.READ VALUE USING GTS (TR/B-DOOR LOCK SW)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tr/B-Door Unlock SW Back door opener switch (open switch) OFF or ON OFF: Back door opener switch (open switch) not pressed
ON: Back door opener switch (open switch) pressed
-
Body Electrical > Entry&Start > Data List
Tester Display
Tr/B-Door Unlock SW
50003 125 17
OK:

The GTS displays ON or OFF according to the back door opener switch (open switch) operation.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

3.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY
3.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY

OK

4.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)

NG

REPLACE BACK DOOR OPENER SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)
a.

Disconnect the M5 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W11-3 (UL) - M5-26 (TSW5) Always Below 1 Ω
W11-2 (E) - Body ground Always Below 1 Ω
W11-3 (UL) or M5-26 (TSW5) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY

Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION

Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)

NG

REPLACE BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
a.

Disconnect the 4D instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W12-1 (ACT+) - 4D-20 Always Below 1 Ω
W12-2 (ACT-) - Body ground Always Below 1 Ω
W12-1 (ACT+) or 4D-20 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Replace the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK BACK DOOR OPEN OPERATION
8.CHECK BACK DOOR OPEN OPERATION
a.

Check that the back door can be opened.

OK:

The back door can be opened.


Result:
Proceed to
OK
NG




OK

END (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)