Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM
RM37A0E _58 Vehicle Interior _086884 DOOR LOCK _0417739 WIRELESS DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  No Answer-Back  


DESCRIPTION

In some cases, wireless door lock control functions are normal but the hazard warning light and wireless door lock buzzer* answer-back function do not operate. In such cases, hazard warning light and wireless door lock buzzer* signal outputs from the main body ECU (multiplex network body ECU) may be malfunctioning.

*: w/ Wireless Door Lock Buzzer Answer-back Function


WIRING DIAGRAM

B472430E35
0.24,2.094 1.156,2.292 0.917,0.198 10 false A22 0.229,2.24 2.208,2.594 1.979,0.354 10 false Wireless Door Lock Buzzer* 1.906,1.552 2.271,1.781 0.365,0.229 10 false 1 0.573,1.542 0.938,1.771 0.365,0.229 10 false 2 2.406,1.563 2.771,1.792 0.365,0.229 10 false 29 3.521,1.573 3.885,1.802 0.365,0.229 10 false 21 3.75,1.573 4.115,1.802 0.365,0.229 10 false BZR 3.406,2.917 3.771,3.146 0.365,0.229 10 false MB 3.406,3.083 5.042,3.771 1.635,0.688 10 false Main Body ECU (Multiplex Network Body ECU) 2.094,2.354 3.698,2.958 1.604,0.604 10 false Instrument Panel Junction Block Assembly* 2.094,2.208 2.458,2.438 0.365,0.229 10 false 4C 0.708,4.344 2.583,4.615 1.875,0.271 10 false : CAN Communication Line 5.656,3.125 6.833,3.802 1.177,0.677 10 false Combination Meter Assembly 4.052,1.135 4.469,1.323 0.417,0.188 10 false 12 V 0.271,3.865 3.781,4.156 3.51,0.292 10 false *: w/ Wireless Door Lock Buzzer Answer-back Function

CAUTION / NOTICE / HINT

NOTICE:
·

The wireless door lock control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the wireless door lock control system after confirming that the communication system is functioning properly.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

Before performing the inspection, check that DTC B1242 is not output.

·

The auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.CHECK CUSTOMIZE SETTING USING GTS (HAZARD ANSWER BACK, WIRELESS BUZZER RESP, WIRELESS BUZZER VOL)
a.

Select the setting by referring to the table below.

Wireless Door Lock
Tester Display Description Default Setting ECU
Hazard Answer Back Function that flashes the hazard warning lights once when the doors are locked by wireless operation and twice when the doors are unlocked by wireless operation*1 ON 0:OFF,1:ON Main body ECU (Multiplex network body ECU)
Wireless Buzzer Resp Function that enables/disables the wireless door lock buzzer response*2 ON 0:OFF,1:ON Main body ECU (Multiplex network body ECU)
Wireless Buzzer Vol Function that adjusts the wireless door lock buzzer volume*2 Level5 0000:Level7,0001:Level6,0010:Level5,0011:Level4,0100:Level3,0101:Level2,0110:Level1,0111:Level0 Main body ECU (Multiplex network body ECU)
50006 1

*1: Vehicles displaying the Item "Hazard Answer Back" on the GTS

*2: w/ Wireless Door Lock Buzzer Answer-back Function



Result:
Result Proceed to
All settings are ON and other than Level0 A
A setting is OFF or Level0 B



A

2.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS

B

2.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
a.

Check the wireless door lock control function using the electrical key transmitter sub-assembly.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock/unlock operates properly A
Wireless door lock/unlock does not operate properly B



A

3.READ VALUE USING GTS (FR DOOR LOCK POS, FL DOOR LOCK POS, RR-DOOR LOCK POS SW, RL-DOOR LOCK POS SW)

B

3.READ VALUE USING GTS (FR DOOR LOCK POS, FL DOOR LOCK POS, RR-DOOR LOCK POS SW, RL-DOOR LOCK POS SW)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Lock Pos Front door RH unlock detection switch signal LOCK or UNLOCK LOCK: Front door RH locked
UNLOCK: Front door RH unlocked
-
FL Door Lock Pos Front door LH unlock detection switch signal LOCK or UNLOCK LOCK: Front door LH locked
UNLOCK: Front door LH unlocked
-
RR-Door Lock Pos SW Rear door RH unlock detection switch signal OFF or ON OFF: Rear door RH locked
ON: Rear door RH unlocked
-
RL-Door Lock Pos SW Rear door LH unlock detection switch signal OFF or ON OFF: Rear door LH locked
ON: Rear door LH unlocked
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Lock Pos
FL Door Lock Pos
RR-Door Lock Pos SW
RL-Door Lock Pos SW
50003 123 196,198,51,52

OK:

The GTS display changes correctly in response to the lock/unlock operation.


Result:
Proceed to
OK
NG



OK

4.CHECK WIRELESS ANSWER-BACK OPERATION

NG

GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit)

4.CHECK WIRELESS ANSWER-BACK OPERATION
a.

Check the wireless answer-back operation using the electrical key transmitter sub-assembly.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Result Proceed to
Only wireless door lock buzzer answer-back does not occur. (w/ Wireless Door Lock Buzzer Answer-back Function) A
Only hazard warning light answer-back does not occur. B



A

5.PERFORM ACTIVE TEST USING GTS (WIRELESS BUZZER)

B

9.CHECK HAZARD WARNING LIGHTS OPERATION
5.PERFORM ACTIVE TEST USING GTS (WIRELESS BUZZER)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Wireless Buzzer Wireless door lock buzzer OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Wireless Buzzer
50004 123 12

Result:
Result Proceed to
Wireless door lock buzzer does not sound A
Wireless door lock buzzer sounds B



A

6.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

6.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Disconnect the A22 wireless door lock buzzer connector.


b.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Wireless Buzzer Wireless door lock buzzer OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Wireless Buzzer
50004 123 12

c.
B222362C84
1.469,0.417 1.885,0.667 0.417,0.25 0.24,0.198 0.552,0.396 0.313,0.198 10 false *a 1.552,0.458 1.865,0.656 0.313,0.198 10 false A22
*a Front view of wire harness connector
(to Wireless Door Lock Buzzer)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A22-1- A22-2 Active Test Wireless Buzzer is OFF Below 1 V
Active Test Wireless Buzzer is ON Pulse generation
(frequency: 2 kHz, high voltage: 11 to 14 V, low voltage: below 1 V)



Result:
Proceed to
OK
NG



OK

REPLACE WIRELESS DOOR LOCK BUZZER

NG

7.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
7.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Reconnect the instrument panel junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A22-1 - MB-21 (BZR) Always Below 1 Ω
A22-2 - Body ground Always Below 1 Ω
A22-1 or MB-21 (BZR) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

8.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
8.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4C instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A22-1 - 4C-29 Always Below 1 Ω
A22-1 or 4C-29 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HAZARD WARNING LIGHTS OPERATION
a.

Check that the hazard warning lights blink when the hazard warning signal switch is pressed.


OK:

Hazard warning lights blink.


Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

GO TO LIGHTING SYSTEM (Proceed to Hazard Warning Switch Circuit)